how many people you got already? if you havent got 10 im in.. but i wont give money until i see the products though...(bad experience with yashar)
Aftermarket Sway bar endlinks
- Thread starter YoNkErS87t
- Start date
There's a pic of them on the first page. Very nice IMO. Outofstep has a pretty good rep here, I trust him with my money.
I had the parts laying around here for a few weeks, but my passenger side endlink finally popped, and was louder than hell. So I finally went to a hardware store, bought some threaded rod, and put them together. The loud clacking sound is gone and the steering has gained a lot of response 
Unfortunately I am not able to put the rears on yeat because I need to reinforce the mounting tabs back there, and I have no welder...
Unfortunately I am not able to put the rears on yeat because I need to reinforce the mounting tabs back there, and I have no welder...Attachments
G
gotboost$
Guest
You can count me in at that price... when your ready. Post in the group buy section and ill send in my down payment
rock on man!
thanks for supporting the Supra community with great parts!
rock on man!
thanks for supporting the Supra community with great parts!
oneandgone said:
lol not what i meant... i mean when he starts shipping out...then ill pay
and yes trust... :icon_sad:
i dunno but after the group buy of the selhoute tail light cover i lost em... :icon_sad:
That wasn't me. I can't help it if someone lies to me about their intentions. I did however give Yashar's contacts information and told everyone how to report him to the FBI/RCMP.
I knew crap like this would happen from it. Even though I personaly have had multiple successful group buys, Yashar drags my name through the mud.
Actually, here's what I'll do. Don't worry bout a group buy. If you want adjustable endlinks for all four corners, send me a PM. 185 bucks + shipping.
I knew crap like this would happen from it. Even though I personaly have had multiple successful group buys, Yashar drags my name through the mud.
Actually, here's what I'll do. Don't worry bout a group buy. If you want adjustable endlinks for all four corners, send me a PM. 185 bucks + shipping.
Aren't the parts for these type of assemblies dirt cheap and fairly accessable? For some reason I remember a friend throwing together a set of rear adjustable toe-links for his AW11 for next to nothing and wasn't steeply 'mechanically inclined'. I am :nuts: so I could be way off base.
Boostedstr8six said:
You are correct. I did mine with nice spherical rod ends that were 7.81 each. 8 were needed, and I also needed some threaded rod, jam nuts, washers, and nylock nuts. All together it was under 75$.
SoupedUpSupra said:
Yeah and you got them all from where... Ace Hardware?
The type of rod ends that Im personally using are teflon coated, anodized red 6061 aluminum racing rod ends.
They won't wear out any time soon, and they are the best quality.
Stop being cheap... you get what you pay for.
:crazy1:
well... that is ALMOST the best quality... im going to assmble mine with the plethora of Toyota aeromotive hardware my dad (whjos building an airplane, coincidentally) has... so
MDCmotorsports said:
I don't see how I am being cheap by making my own endlinks, I used Teflon coated steel rod ends, so to be honest with you, yours will wear out before mine. I got my parts from www.aedmotorsport.com by the way. So don't go running your mouth before asking.
G
gotboost$
Guest
SoupedUpSupra said:
Same source as me, they are a great resource. However I use the race series heims, they run 2.5+ times more than yours. Stuff as important as suspension linkage, I don't cheap out.
Different routes for different folks I suppose. I make very little on money on these.
I'm going to go ahead and make three full sets. My wallet right now doesn't allow for ordering more supplies than that. If you want a full set, shoot me a PM.
F-me...
I really put the cart in front of the horse on this one. The heims I use are substantially more expensive now then they were the last time I made a set. I can't do 185 a set non-GB. It will now have to be 215 a complete set for non-GB price. I will not use lower quality heims, so I can't get the price lower than that.
I would need to do a GB of 7+ (once again, different prices at different quantity break points from the manufacturer) for the price to be 185 for a full set.
I sincerely apologize for this.
I really put the cart in front of the horse on this one. The heims I use are substantially more expensive now then they were the last time I made a set. I can't do 185 a set non-GB. It will now have to be 215 a complete set for non-GB price. I will not use lower quality heims, so I can't get the price lower than that.
I would need to do a GB of 7+ (once again, different prices at different quantity break points from the manufacturer) for the price to be 185 for a full set.
I sincerely apologize for this.
I have them now.
I was trying to wait out on stepping on any ones toes.... but that went out the door. :rant:
Sooo....
I have a front and rear pair in stock.
Cost is $125 each end, total of $250 for the whole car.
The KIT includes every thing to put them on in an afternoon.
EVERY NUT, BOLT, AND OTHER ITEM THAT YOU CAN POSSIBLY IMMAGINE IS IN THIS KIT.
And I don't have a pic cause my camera is a POS.
All hardware is stainless and the washers and endlinks are 6061-t6 aluminum.
Pm me or email me if interested.
I was trying to wait out on stepping on any ones toes.... but that went out the door. :rant:
Sooo....
I have a front and rear pair in stock.
Cost is $125 each end, total of $250 for the whole car.
The KIT includes every thing to put them on in an afternoon.
EVERY NUT, BOLT, AND OTHER ITEM THAT YOU CAN POSSIBLY IMMAGINE IS IN THIS KIT.
And I don't have a pic cause my camera is a POS.
All hardware is stainless and the washers and endlinks are 6061-t6 aluminum.
Pm me or email me if interested.