Hello guys
Would anyone know what is the outside diameter and inside diameter of the 2 Circular gaskets that go betweeen the cast iron twin manifold to turbos cheers
Hello guys
Just installed a new 6 puck clutch 1JZ supra....Clutch shifts fine little bit of shudder as expected but for some reason at 10kms-80kms there is this massive banging, klanging noise enough for people on the street to hear it. ive replaced the centre bearing with a 2nd hand one as...
Hello Guys
ive gone thru my 3rd slave 1st = came with car then leaked after couple months, 2nd = second hand purchased from supraforums leaked then broke where the bolt goes then 3rd now leaking. ive got the 1st non broken one left is there any kits I can buy over the counter to rebuild this...
Hello guys specs on my car
1988 MA70 with T61 turbo running AUTO box. it seems to be very very laggy like boost doesn't kick in till 3500rpm. I wish I kept the CT26! with no boost controller it boosts to 18 very quick ive tried another boost controller and still rubbish :: angry ::
finally got aircon regassed by a mate. It works fine only if I connect the clutch stright to 12V. have tested pressure sensor and that is fine. problem is I push the AC button and turn on fans and nothing happens. I have bridged the 12V from the AC relay plug and if I turn the air fan off the...
Hello Guys
I’ve converted my MA70 automatic to 1JZGTE 5sp R154 Using full JZA70 engine bay, interior looms. the MA70 had abs brakes so I obtained the correct rear speed sensor and dissected the abs wiring out of the MA70 looms. I’ve left the NL, PL wires disconnected and for the BATT wire...
Hello guys
Im running a 1JZGTE and JZA70 engine bay and engine looms in my MA70 now ive got all the compnants for the ABS still in the car so want to run that also have the correct r154 sensor question is there is a few wires that come out of the MA70 abs computer that I dont know what to do...
Hello guys ive got a wierd issue!!
My Jza70 tacho guage doesnt work! everything else works. ive run a wire stright from the ignitor to the plug at the dash and no change it doesnt even budge also tried another dash and that didnt work! is there any dash wires like earths or relays that...
Hello guys whilst I was swapping in my JZA70 interior wiring loom into my new MA70 shell I noticed a blue box called OK monitor and this wasnt plugged in :aigo: question is what does it do?
Hello guys
Im converting my MA70 to 1JZgte and using complete 1JZ body, engine and engine bay looms. now my car has ABS which i want to retain if possible. ill be seperating the ABS looms from the MA70 wiring. question is will the rear AUTO abs speed sensor work in the r154 gearbox? I can...
hello guys
Have an issue with external waste gate. currenty ive got it setup as side port to boost controller to Comp housing. ive also tried top and side port(2ndtry) TEEed off to boost controller then comp hosing. PROBLEM 1 current setup it will not go past 7psi! no matter what I do to...
Hello guys I would like to know the measurements from bolt hole to bolt hole upo down etc also the overall size of the flange. unfortuently I can measure as turbo is on car :: angry :: also the size of the entry hole
Hi guys
Ive got a set of newish 7MGTE coilpacks will they work with the 1JZ using stock ECU and ignitor? has it been done before. Mine are badly cracked and since there sitting around I can make use of them!
Hello Guys
Since swapping to my correct MA70 supra loom my temp gauge is going stright to hot after 2mins of running. Motor is cool to touch lol Ive already ran A wire stright from temp sensor to dash loom plug issue still occurs. besides replacing it with an aftermarket gauge what could be...
Hi guys
Currently to start my car I need to bridge FP and B+. ive check the loom and every thing goes to the correct area. with my modified cressida loom and ecu it started and ran fine. Ive noticed attaching a multimeter to yellow FP wire out of ecu while cranking shows volts going up then...
Hello Guys
I got hold of a Manual ecu(yellow plug big), wiring loom, dizzy and injectors and duel manifold. questions are can I use my cressida/supra 92 injectors and dizzy with the yellow plug ecu? my green injectors use a grey plug ecu and have no resistor pack. is it possible to use the...
Hi Guys my supra had squashed front stone deflectors. So i've taken one off and was going to make one to weld in but something has come up.
I got my 2mates and one has a hardtop and other Targa top both 1990 and its missing them like factory sealer where they would go. According to the epc Z20...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.