Search results

nice start!! wut do i see?? 1uzfe?

Any shots of how its wired up or hooked up in the back? Did you just use the connections on the flexible circuit board?

At first i thought crap another i wrecked my car thread. But the Cygnus CAR!!!!!! There goes a HUGE chunk of the supra community. Very very sorry and sad to see that car go, it may not be pushing 800+ hp but it made damn sure that anyone w/ an internet browser could find out how to get there...

well after extensive testing and searching w/ a multimeter and checking the TSRM we bypassed the fuel pump relay w/ jumpers in the diagnostic box, tryed the 12 volt mod, checked the voltage being sent through the harness, checked the resistance of the cables in the fuel pump harness. dropped...

NOPE!!!, Its baaaaaaack. got it to run and reconfigured my lc-1 and all so the maftpro was reading afr!!!!!, then it choked out and died and im back to the Fuel pump issue. "the jumpers, they do nothing!" back to the drawing board. ~Luis

figured i'd post SOMETHING, car is moving backwards as it seams. Dyno is in 2 days and i SERIOUSLY doubt the car is going to make it down there, im doubting it will make it out of my driveway at this point. Having some troublesome issues w/ the wideband signal going from tip top stoich 14.7 to...

The BLUE and WHITE wires should all be grounded to the same ground source and although these grounds are of the same source, the BLUE wire should be wired separate from the WHITE wire to avoid analog ground noise. Optimally, these (and any other MTS device ground) will be soldered to the same...

upon further inspection and digging i got hit in the face w/ the reality that the innovate lc-1 harness is missing the green analog ground wire. Did they change it? or did i just get the 1 lc-1 w/ an incomplete harness?? anyway around this? Im assuming this is my problem considering it is the...

Here you go, as hi res as i can host. http://img339.imageshack.us/img339/4595/dscf3280hw3.jpg http://img256.imageshack.us/img256/8730/dscf3584gc2.jpg i got more if ya want'em

hey man did you resolve this issue??? I am having the same problem. Car starts up fine and idles great for a while. After about 10 minutes of idling the AFR signal to the maftpro cuts out and i get the two little -- in the sensor monitor on the maftpro. But my AFR guage still reads the AFR, it...

srry to hear about your grandpa man, sometimes ya gotta change priorities. I'm in the same boat car is on the sidelines till i get lifes issues fired up and running good. We WILL make it to suprafest though, im calling you out.

what setting do you have in the maftpro, i set it up as sealevel because i didnt know what the other settings meant and couldnt find definitions in the quick setup sheet. I KNOW its hooked up to the right wire on the ecu and T-pro i speant an extensive amount of time labeling and checking my...

i hunted on there for a while for the 4.8 stuff, should create an account too i guess. anyway, i did the 89+ ecu hac mod as stated here. http://www.supramania.com/forums/showthread.php?t=32205&highlight=HAC, you do it differently?, i wanna get tunerpro setup so i can load a bin and locate...

fire your mechanic, but if he knows anything he'll know that its better WITH one. There probably a reason you keep having to go back to him. picked one up from toyota a bit ago ~$130. have him take that off of your tab.

ok i've been reading a whole mess of pages in this thread and been searching ALL OVER but i just CANT find a few minor things I need in order to get the tunerpro to read w/ my 4.80 firmware in the mafpro. what i need xdf files ALDL files pretty much everything i need to load into the tunerpro...