Search results

That sounds good & would love to have you join the caravan from Louisville but thats 2hrs out of your way. Just jump on I70 east & your there in less then 2 hrs. We are 2 hrs away from you now & 2.5 hrs from Dayton. Louisville Group will be leaving Friday late AM/early PM with meet place &...

Absolutely a great time. It was great to see Rupinder, Lynn, Bob, Marino & Al Jorden. again. Steve, Anthony, & Graham I'm glad I got to meet. It was a blast to hang out, talk about times old & new. Rupinder & Marino your Supras looked as clean & perfect as any could be, Truly pristine. AJ you...

I'll be getting there late am earliy afternoon. Here is a mapquest link to Fast Enough performance...

ok here is the web page with details. http://www.thunderoverlouisville.org/ I know a few of you esp Ben like Air shows so it would be great to check out.

Looks like Friday is the only day I can catch up with everyone. If you guys don't have set plans for the 21st Sat. night Think about making it to Thunder Over Louisville. Opening ceramony for the Kentucky Derby with an Air show and one of the largest fireworks shows in the world.

Ok, Got the registration sent in. See you there. Anyone that wants to caravan out from Louisville Friday Afternoon LMK

I will make it out again. Look forward to seeing you guys again.

Sounds like what mine did. I had a bad Vacuum line source connected to the map sensor. Once I pluged in a viable source all is cherry.

Thanks Guys. Yea Stefan my initial problem was caused by a BAD Vacuum source. From link you posted I 1st pluged it into the 25706 pipe. There are 2 VAc lines which runs to the FPR & TB. I used the one to the TB. Bad Idea cause it caused all my problems. I used the vac line going to the stock...

Yea it is. Thanks anyway however I got it to work. Turns out once I learned how to read the settins I seen my TPS was out. Reading .18 TP closed & 2.6 fully open. Ouch! I set it to .5 closed but I can only get 3.7 fully open. Also I had the MAP vac. line near the FPR vac. line. Switchd...

I just installed the Maft Pro w/speed dens. & used the "Quick Setup 4.40" sheet for initial settings. Wired as instructed & everything is connected but not soldered yet. I have the Map sens on the driver side fender w/vacuum line connected to the port above the FPR Vac. line. The AIT is just...

While shopping for a New Radiator I ran across this one by Haste Engineering. Anyone use this or know about there quality in general? http://cgi.ebay.com/ebaymotors/Haste-86-92-Toyota-Supra-JZA70-Manual-Aluminum-Radiator_W0QQcmdZViewItemQQcategoryZ33602QQitemZ180101243707QQrdZ1QQsspagenameZWDVW

I'll be there Sat & Sun. You should post this in the Midwest section also. I'm sure you could draw folks from IN, KY etc.

Not sure, but its ran by Chris Bogle. Email him for details: faturbo1@bellsouth.net & FATurbo1@aol.com. I have gotten alot of parts from him. He is a great seller.

Well that sound easy enough. Thanks

Well I have the pump, wire harness, & filter. None of the clamps, hose etc. on the bottom of pic.

I will be doing this shortly & I have everything but the Walbro install kit. Whats in this kit so I can source localy? If I need just the kit who would I order it from? Thanks

Very well put bgrieger. fstoy My 1st stop would have been the County Attornys office. Hit him up with Theft by Deception charge for the bad chack. In this case is a Felony.

How long ago did he skip? If its more then 6 mos then Try Zabasearch.com Put in his name & state & it will pop up his address. There data base is updated via the credit agenceys & utilitity co's. So if he is renting & has utilities in his name he will pop up. Also do a search for family...

It functions very well on a stock or upgraded CT. At least thats what I have exprenced last 3 yrs. Now once I upgrade to a larger Turbo this spring I may change it out. :naughty: