Search results

Im an hour north of the twin cities. But I come down all the time.

Yes its a 1jz in my S13. What I need to know is will a Toyota release bearing work with a ORC single plate? ORC lists 3 different size bearings and I dont know what one my setup has.

A couple of friend said it was a release bearing and I really dont want to pull it out till I get the part. I need to basically pull everything out of my engine bay to pull the motor and trans. This is in my S13. But what I really am wondering is if a Toyota bearing will work?

So my 1jz came with a ORC single plate and the release bearing is making some noise when I press the clutch. What I need to know is do I need to get a bearing from ORC or will a Toyota replacement work. Nengun.com list 3 different size bearings and I dont know what one I have. Any input is...

Sorry I should have stated some of the things I have already done. I have replaced the plugs with NGK Iridiums for a 2j, replaced the TPS, checked all the coil packs, unplugged each cam sensor while running and it got worse when unplugged. I also should mention that I don't have that fuel...

So I finally got my 1j running in my S13. It idles rough and has no power. I drive the thing in the parking lot and it hesitates and doesnt have power. Once it starts to rev it smooths out. The throttle isnt very responsive. The air fuel ratio at idle bounces between 12.9 and 13.1. I am not a...

There is no numbers by the resisters that I am talkin about but I do have 2 really good pics. They are the circled ones. One is a black tower thing that looks a little burnt and then there is a 2 resisters. 1 resister is blue and the other is now burnt brown.

What wires did you have to connect to the ECU to get it to run? I am finishing up the same swap.

My resistors are burnt so bad that I can tell the color stripes. So frustrated.

I would totally do that but I know how to do the work and need it by this weekend. I have dealt with Driftmotion many times and have been pleased every time.

I have been looking online for the past 4hrs and cant find any ECU motherboard diagrams for a 1jz ecu. I have some burnt resistors and the shop doesnt know what to replace them with since they are bad. If anyone can get me pics or a diagram that would be great. Oh and the ecu is a...

Damn. Lookin good. My car is very very close to being done.

Sorry I couldnt make it. Got super caught up with workin on my car. I need to get it done.

Sounds like fun. I will actually be in the area picking up my R154 from Primo from getting my shifter modified so I might stop by to meet some of you folks. I wont be in my S13:icon_frow

I am in the middle of swapping a 1j with a R154 into my S13 any my trans doesnt have any speed sensor. It is just an open hole. What sensor do I need to get a my speedo to work. I know I will need the interface box thing. Also what is the 2 wires on the pass. side of the trans for? Thanks.

So I had read that I can use a 2jzgte tps on a 1jz and I had my Toyota dealer get me one and it doesn't fit. Did I miss read something? When I ordered it I ordered it for a 1995 Supra twin turbo. Did I order the wrong one? Is there one I can order that will work? Thanks.

Very crazy busy weekend. Got a little bit done. And some color shot. Some epoxy primer/sealer Painted the cage More to do. Lots more to do.

Man that sounds and looks good.

Yup and I am a Nitrous junkie. I love it.

I have a SR but I think I am goin to put it in my AE86. I am goin with Nitrous because I have a wet kit from one of my old cars and I got a Intercooler kit for doin a side job. I will have boost and maybe something else in the future.