Search results

Looking for the diameter of the 7M Engine harness hole and Speedo Cable hole. Need to order some block-off grommets and my car is 1000km south from me. :( If anyone has the time to do this, I'd really appreciate it.

Since I'm close to finally completing my 1JZ swap, I've been thinking about drag racing again and how I should setup the car while maintaining streetable-ness. Here is my proposed setup, any and all feedback is appreciated: - RX7 rims in rear with 26x10.5 MT ET Streets OR 15x8 Welds with...

I'm in the midst of a 1JZ swap and am trying to figure out how far I will need to extend the body plugs...will it be 18" just like the ECU plugs? The reason I ask is because my car is 1000kms away from me, but I have the 1JZ harness and two 7MGTE donor harnesses with me and would like to have...

I seem to have misplaced the bolts that hold up the tranny crossmember. Does anyone know what size they are?

I had ordered & received a replacement clutch disc for my 87T a couple years ago...long story short, the 7M blew up, I pulled/parted it and the car has sat ever since, waiting for the 1JZ to go in. Today, I was putting together all the drivetrain bits in order to bolt the tranny back onto the...

I'm in the midst of building a custom instrument panel and changing out the LEDs in the climate control. I plan on using 5mm indicator lights in the cluster (signals - green, hi-beam - blue, tems - green, hi/low boost - red, launch control - red, 2-step - red, trac control - red, etc.) and have...

I'm in the midst of building a Plug-N-Play harness to go from the 1JZ engine harness to my Megasquirt. I will be routing the 1JZ harness through the OEM harness hole (LHD) and was wondering how close it reaches to the OEM ECU location? I need to know so I can go ahead and cut all of my wiring...

Well, it appears that my GT35R compressor wheel ate itself...I highly doubt something was sucked into the intake tract. One of the compressor fins appears to have broken off, causing catastrophic damage to the rest of the fins. Now...apparently Garrett does not sell the compressor wheel by...

I should've known to never buy a car with a "built" engine...you'll just get bent over in the end. Did a compression test today on the car b/c I noticed it was blowing blue smoke after it idled for a few minutes and it would blow blue after I hit boost (~15psi on a GT35R) Compression...

I bought a pair of "87-88 Foglights" yet they don't bolt up. The holes on the foglight brackets are spaced further apart than the mounting points on the car. Does anyone have pics of these brackets side by side?

I've sent two PMs to Jon since Jan. 2 with no response. I was going to make a post in his forum regarding this, but it has disappeared? Jon, can you please respond to my PM.

Finally received them after waiting 8 weeks...ah well, all good things come to those who wait, right...;) Anyways, if you saw the license plate "TRB0SLT" on a Supra, would you understand what it meant (I'm sure all of you will know better than the general public, but I'm curious)...

The turbo is fine, but I was curious about a few things. Is it possible to rebuild it with a DBB center cartridge? Can the wheels be swapped out with GT wheels?

I know it might not seem like *much* of race considering I'm running a T78, but it's just on the Lex/550 combo...basically, "untuned"...don't have the ability to lean out the mixture to produce more power...yet. :evil2: My car: - 7M-GTE - T78-29D turbo - 14psi - SSauto header - 50mm wastegate...

Anyone ever have one leak from around the top seam where the lip is folded over? I just finished installing my 550s and was testing for leaks (connecting Fp and B+ on the diag. port) and found out the damper is leaking... :( I've changed out injectors 2 or 3 times now (when trying to get the...

Just finished installing a new header, turbo, Lex AFM and 550cc injectors. I am also using the Lexus electronics on the AFM (have read they are the same as the stock Supra). I'm having some trouble getting the car to run correctly...it seems to flood itself (difficult to get it to actually...

I'm replacing my Toyota O2 sensor with a 3-wire Mustang LX O2. Curious about the wiring though. On the 'Yota sensor, there is a single blue wire and two black wires (grounds?)...on the Mustang sensor there is a single white wire and two black wires(grounds?). Am I correct in assuming that...

Hopefully I'll be able to start/complete the swap this weekend...finally...been over 2 months now w/o turbo... :( Anyways... :naughty: Thinking about the swap got me wondering about the coolant lines on the CT-26. What do I do with those? How do I "cap" them off or loop them? Are the...

More specifically I need to know what thread pitch I need on the 12mm to -4AN adapter...is it 12x1.25 or 12x1.5?

My brother bought me a Kaixen H4D (Hi/Lo) HID kit as an X-mas gift and I finally got around to installing them. :D They are 6000K bulbs. The lamps are Hella E-code H4 housings. Only $115CDN from PG Performance! These things throw ALOT more light out there AND they don't blind oncoming...