Search results

Hello. With a big smile on my face I finally managed to get a second hand HKS Twin Power DLI as I always wanted. I have a 1jz swap in MK3 Supra. I hooked HKS DLI the way as guides say, for example this one: http://www.soarerworld.com/forum/showthread.php?t=17138 HKS 6 yellow wires - 1jz...

Hello. I bought a HKS Twin Power DLI type unit recently. I want to connect it to my 1JZ. It's second hand so I would like to know is there any way to check or measure something to find out is it working correctly? I have 1JZ swap in my Supra MK III and I don't know this engine, so I wont feel...

Hello. Let me begin with some facts: Fuse box from under the hood AKA- J/B no.2 is connected with positive battery terminal via white thick wire. Although this wire is not connected directly to battery. The whole circuit is protected from any problems that can occur on the line between battery...

Subject mentioned many times. I know because I did the same kind of swap (replaced N/A engine with turbo) and I saw many answer looking for a way to put my tacho back online. I even imported whole jza70 dash cluster from Japan ;) N/A tacho reads different kind of signal, that's why it doesn't...

lil' update -alt not working -tacho not working -need to make custom hubs to fit brembos with rotors from EVO VIII good points... 6-layer paint, anti-rust front

followed by 1JZ swap guide from forum http://www.supramania.com/forums/showthread.php?43888-**How-to-wire-a-soarer-1JZ-into-MA70** and alternator doesn't charge :( tried old alternator plug wired into new one or EB1 EB2 plugs as mentioned in guide but no change.

soldering iron powered extension of loom fitted, wired, plugged, starts but still under construction stripped front for new anti rust layer and facelift parts still big, less ugly :p ma70 and jza70 dash to replace tacho module replaced in ma70 tacho to keep other faces...

waitin' for custom brackets to fit them

Long time no see... Lil progress since last time. Got some new toys like strong braking will :evil2: of EVO VIII 4 & 2-pot Brembos with Performance Friction front rotors and muuuu pads ;) customized brackets will put this setup on car soon. Together gonna do the job with Rays...

I wired 1jz alternator to old 7m plug wires and no change. I checked also this way: but still no alt charge :(

Hi folks! Got some problems during swap job. I did everything, step by step, each wire after each wire with sticky thread **How to wire a soarer 1JZ into MA70** from above. 1JZ alternator is plugged to it's harness and old alternator plug is wirred as it comes: yellow (L) -> black EB1 plug...

Thanx for reply ;) No, I didn't put that question elsewhere.

just in case of rising boost by 0.2 bar You thing 6 heat range if enough for such setup? Anyway 1.1mm or 0.8mm gap then?

Hello there. I just swapped 1JZ-GTE from Toyota Soarer into my MA70 body. I'm about to change spark plugs. I know I want NGK iridium plugs with 7 heat range (1 step cooler from the stock ones) but don't know which gap size to choose. BKR7EIX with 031" (0.8mm) gap or BKR7EIX-11 with 043" (1.1mm)...

Well... the same years of production for different markets didn't look the same. USDM got some upgrades earlier. I read also this thread about major changes: http://www.toyotanation.com/forum/showthread.php?t=101639l Red one is '91 or maybe '90? Doesn't matter as long as it got R154 gearbox -...

Time to gather some resurrection required parts: JZZ30 - Toyota powered by the forgotten hero - 1JZ-GTE Supra 7M-GTE M/T - R154 gearbox keeper 1JZ and R154 bell housing Exedy Hyper Single clutch and some other helpful stuff: -lightweight underdrive pulley kit -Paraut...

parts for euro and new cars... but for Japan old cars? hmmm... oil and air freshner

Hello and welcome everyone! Let me tell you a story. Far, Far away, long but not so long ago as some of you may think (around 2004), in a forgotten by any god land of Bison grass vodka, beloved with an apple juice in Japan, there was a girl. Girl with love to a moto stuff. Once passin' next to...

With swap many things will change, color also. Hope to make some progress very soon in project as it's paused for a 2 months already!! :/

I got 4-pistons fronts with Performance Friction 2-pieces 32mm thick rotors and 2-pistons rears. Everythin' from EVO VIII, with intention to swap into Supra's hubs somethin' like this one