1JZ Pistons

[dinhnerz]

Does Titan sell the 1jz piston rings alone or do they sell them with the pistons itself as a set?

I'm also in desperate need of piston rings.

 

[Jostar]

Does Titan sell the 1jz pistons alone or do they sell them with the pistons itself?

I'm also in desperate need of piston rings.

Yes they do.

 

[dinhnerz]

disregard this post. lol

 

[Panchira!]

are they stock rings or for forged pistons? whats sean's screen name?

sent the block out on sat with aaron.....hopefully the block is 100% a.ok! if not i dont know what ill do.....

 

[Jostar]

are they stock rings or for forged pistons? whats sean's screen name?

sent the block out on sat with aaron.....hopefully the block is 100% a.ok! if not i dont know what ill do.....

For the forge pistons & his screen name is 2jzmkiii, They even sell rods too for the 1jz, I just finish byuing something for my JZA70 :evil2:

 

[dinhnerz]

I just got an email back from Sean today. They don't have any stock piston rings.... :cry:

 

[Jostar]

I just got an email back from Sean today. They don't have any stock piston rings.... :cry:

That sux buddy, Well try the MR2 3SGTE motor piston rings, I hear there the same.

 

[dinhnerz]

I'm not sure I want to take that risk. If I ever decide to I'll post up how it goes.

 

[525gte]

So I dug up this old ass thread.. and I am about to order pistons. And just want to be clear

2j gte pistons can be run in a 1j stock rod. Correct?

And same goes for if I want to order a cp 2j piston in a 9:1 ratio. I just want to be clear that when I call cp pistons to get my 2j pistons I can put them in my 1j

Sorry for digging up a relic. But its 2 am. I am tired and this is the 1st thread I found on this subject

 

[nathaninwa]

Depends on if the 1j and 2j have same cc combustion chamber too.

 

[Turbo Habanero]

Why not just call cp and ask for 1jz 9:1 pistons? Or call Aaron at driftmotion and he can do it for you.

I'm running CP 9:1 pistons in my 1jz

 

[525gte]

Why not just call cp and ask for 1jz 9:1 pistons? Or call Aaron at driftmotion and he can do it for you.

I'm running CP 9:1 pistons in my 1jz

I am going to do that I just like to look up all the part numbers and info 1st . From I I found it is cp. Number sc7472 86.5mm 9:1

 

[525gte]

I am going to do that I just like to look up all the part numbers and info 1st . From I I found it is cp. Number sc7472 86.5mm 9:1

bought my pistons today got a screaming deal on them from titan motor sports off of ebay for 690$.

now i go tto spend the day googling how much torq the stock rods can hold:0 it never ends lol

 

[ROBAPHENT]

Im running 3SGTE ones

you just cant use the expander bit off the oil rings you reuse the 1jz ones, so you get top ring, second ring and 2 oil rings and reuse the spacer off the old rings

 

[MK3Hitman21]

so you can use 2jzge pistons on 1jz rods?

 

[525gte]

so you can use 2jzge pistons on 1jz rods?

I belive so just have to get the right compression. The pistions I ordered about make 10 to1 iirc on a 2j. And 9:1 on a 1j due to the stroke differance

 

[MK3Hitman21]

stock comp on 2jzge is 10 to 1, stock comp on a 1jzgte is 8 5 to 1, so i like higher comp ratings. so maybe comp would round 9 to 1 in a 1jz with 2jzge pistons

 

[525gte]

Googgle it up. I came up with cp part number sc7472. And that will get get 86.5mm9:1. Its the same as 10:1 part number for the 2j. That's tahken off cp web site

 

[MK3Hitman21]

yea cause forged oem 2jzge pistons are way cheaper than cp piston. i can go to a engine dismantler and get a 2jzge block hella cheap

 

[525gte]

yea cause forged oem 2jzge pistons are way cheaper than cp piston. i can go to a engine dismantler and get a 2jzge block hella cheap

Are you sure oem are forged ?. I don't belive they are. If they were no one would ever replace them