Hi guys,
Can anyone point me to a picture of the Supra Auto Tranny cooler lines which are mounted on the tranny sides? I need to see the where and how the brackets for those hard lines are placed.
If someone can take a picture , that would be awesome. The tsrm does not show those lines...
OK, so removed the Torque Converter from the busted engine and was going to put it on the good engine. Now when I look at the housing that covers the crank shaft/rear oil seal. the recessed area on the crankshaft end looks larger in the old 7m compared to the one I am replacing it with.
Will...
Okay, I am ready to drop this engine in my Cressida, but while cleaningout all metal piping and stuff, I found out that the crankcase ventilation pipes and the the end that goes to the throttle body is 100% blocked with sludge.
I have soaked it in some fluid to see if I can poke all of it out...
Hi guys:
I need the correct name of these seals to tell the parts guy.
There are two here > not the same though.
Its inserted into the two bigger holes in the Lower timing cover / back plate and sites behind the crank Pulley against the block.
One hole is for the Timing Belt Sprocket. (...
OK, My heater is not working after this swap. Checked the heater wires and they are hooked up correctly to the harness and the coresponding dash harness . ( 1jz )
Heater valve works when vacumn is applied directly bypassing the vsv.
Tried two different VSVs and tried controlling the heat...
Ok....here goes.
I will be attempting to install this red LED in place of the "TURBO" light on my 1g-gte tach. Not sureif it will work or not, but I am thinking of wiring the positive to the pressure signal wire of the stock boost gauge and then grounding the other end.
Someone stated to...
OK : Searched and found the thread, but the actual bulb replacement/color change thread has been deleted. All that is left of it is chatter.....soooo
Only question I have is,
1 - I want to change the color of my gauge cluster lights. Do I have to change all the bulbs to the color of my...
hi guys,
what locations are you using to mount the engine on the engine stand.?
What locations are bolted on?
I could not line up mine with the 7m block.
Thanks.
Moe,
Okay,
I just finished this in my car.
The 1G Tach works with the 1jz setup. It is exactly the same as I checked the circuitry as well. resistors and the diodes are the same. I had one in my car but it was not running.
I checked it out today and the reason it was not working was because the...
I have a set of these just sitting around. Should I put it on or strut around with my mint stock tails?Thanks for the feedback.
Here it is mounted on my car :)
Moe.
With covers:
Without:
For making me very happy on a daily basis....
Hope you all enjoy the new photos I took today....
Go here as the picture quality is a little better eventhough its been resized.Ofcourse the high resolutions are a lot nicer
Owner :Moe > Suprastanger507mgte
Car :1992 MKIII / Targa...
HI guys,
Any ideas on how to free up a siezed motor?
Car was sitting for more than a year and Today I tried to crank it and it won't turn eventhough the starter was kicking. New Battery as well.
I tried to turn the engine via the crankshaft and the engine woudl not budge. I was actually able...
I emailed the the guy in China if he was putting any more of the 1JZ Y-pipe and Down Pipe for sale.
He gave me these numbers for the guy to contact and get them from :
"you can buy them from my friend in usa."
tel:6267153084 or6263308675
Anyways, I don't need any as I was just...
Hi guys,
Don't have any experience with 100 Octane fuel in my car. I was lucky enough to score half a tank of 100 Octane for free, and I took my car to run around 11:00 pm tonight. Its very nice and cool outside.
I was able to feel the difference in performance of my car almost immediately...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.