Search results

I have new wheels, tires, front/rear control arm poly bushings, and brakes. I will be recieving ZP coliovers in a few months. Is it a smart idea or ok to install everything without the new coilovers, or would I be looking at getting an alignment done twice doing it that way?

I found a post similar to the problem I'm having but it is in the 7M forum, and I am dealing with a 1JZ thus my reasoning for this thread. For reference purposes here is the link to the 7M issue: http://www.supramania.com/forums/showthread.php?129750-Gas-leak&highlight=fuel+pressure+damper...

All: I'm attempting to put this together with the idea that once it is corrected and complete, it can be stickied for general reference. Please make any corrections and input as you see fit, all input is greatly appreciated! Thanks...

#1 These guys are on the body of my 89 7MGTE, any idea what they are for and where they go? #2 This guy comes off of near where the alternator is on the 1JZGTE. Is it for the PS rack or something? #3 I know that this is for the heater and that I need to extend it, I think to...

I have on two different sessions attempted no less than 6 times to drop my completely stock 1JZ-GTE into a late 89 chassis. I even pounded a nice dent in the fire wall where the rear turbo will be sitting. I am using Driftmotion's aftermarket mounts and we can get the motor no closer than an...

Hey anyone!! I've prepped my car and 1J to drop in to my 89T. I've got the harness rewired and good to go. Everything is pretty much ready and I could really use some expertise and muscle to just help me get the motor in the car and everything hooked up. Any thing would help and there would...

How do you change the differential oil and what type/weight should be used? I did not see any port on the body housing however I think I got most of the oil out just by having the rear up on jackstands. There has been a very slow oil leak from the main differential oil seal for years on my car...

I knew it prior to doing it but I still did anyway, impatience will always screw you when you are doing this type of work. I rented a torque wrench from Autozone, knowing full well that there is no way in hell it is calibrated and who knows what the hell it has been used for and how it has been...

Does anyone know/remember in which direction the cone spring that goes on the inside of the release bearing faces? When you are installing the spring and then the flat washer, does the cone spring go on the hub so that the cone would be upright or inverted? Page CL-14 of the TSRM...

I can't remember or figure out where the heck I took these off of. Does anyone recognize them? :aigo:

Are there any? Without actually running a turbocharger are there ways of visual inspection (without turbo disassembly) to ensure sound operation?

Has anyone done this while keeping the turbos on the car? Is this possible? I've only been able to remove 2 of the studs on the y-pipe that hold it to the turbines. I don't see how in the hell I'll be able to get to the studs that are on the "motor side" of the y-pipe. Any tips/ advice would...

Can anyone suggest any deletions/ modifications to any 7MGTE engine bay components that are best completed before putting in the 1JZGTE? What about on the 1J itself? Hosing/wiring (I'm waiting on Driftmotion to complete my harness)/ any basic prep to the 1J before the drop in (im changing...

I am in the middle of a 1JZ swap and I have just finished cleaning up my R-154 from the 7MGTE. I have the front and rear main seals for the tranny that I am going to put in, but I want to make sure I complete all preventative maintenance I can to the tranny before it gets mated to the 1J. I...

Ok so I think I've narrowed my choices down. Aside of aesthetics and cost, why would you choose one of these three exhaust sytems over the other? http://www.hksusa.com/products/?id=663 http://store.driftmotion.com/static/i-tanabetouringmedallionformk3supra.php...

I have finally sourced my 1J and will be attempting to pull out the 7M-GTE. Can any one offer any helpful tips that would ensure a smooth process? What are the main tools I will need? I will have access to a 15 ton crane but would an engine hoist be easier to use? Thanks for any and all help...