Search results

Alright I have tried to find the spec in the TSRm, the six bolts that hold the rear cross member or Carrier, they're the huge bolts, Someone told me 156 Ft-lbs.?

Alright, well I am swapping a 1jz into my '92 Supra. I just ordered one and it's coming with. 1JZ motor, Rear Sump, Engine Wiring Harness ( Auto ), ECU, I think the ignitier as well. Will my Auto Trans Hanress work with the manual trans and work correctly when spliced into the 7m hanress and...

Alright everyone I just took paart a '89 7M-Gte. The motor was perfect. Only the two end main caps had wear on the bearings. The crank has no issues. and the pistons came out with easy. my question is, sense everything looked great, can I buy a new bearing set pistons, and use a " I think its...

I am looking to buy a 1jz tonight. i have seen many on ebay. They're 1000.00 with auto trans ecu and ignitor. Can I use the auto harness and ecu on my 5-speed different wiring? Does anyone have a engine? is there anything I should know? Are some ears bad, some good? DO I need front or rear...

I have been looking and I have not seen any differences with a non turbo M?T drive Shaft, compared to a Turbo M?T drive shaft? is there a difference? More power may require a better Drive shaft? Thanks guys!

I just took apart my '89 7m-gte. i noticed that the bearing for the main caps 1 & 7 were wore badly. From what I have learned these are always the two bearing that wear the most, there is more considerable weight on the ends, and vibration for the flywheel, and harmonic balancer. Thank guys.

I read awhile ago that it is note " hard " difficult to remove the oil squirters from the 7m-gte block. Well today I took apart a '89 Engine and if you rotate the crank you can get to, two squirters at a time with easy... I don't get why people say it's hard they can fall into the piston and...

[shaeff edited: information deleted]

Well, I will be starting my search for a front clip with a 2JZ, or a 1JZ. I was curious as to where I could find a good deal. I am not really even sure the places to look, so any address, phone number, or emails you can give me would be great. Thanks for all the helps guys.

Well, just about maybe 10 minutes ago i just took off the whole rear end including the cradle. The rubber spacers look pretty good, but I was curious as to how many people put the nylon ones in? Are there advantages to these?

Is the '89 o2 Sensor plug on the harness round? I want to make sure... I know they make square ones too, so thanks for your input everyone!

Okay well, I decied I am selling my 7m motor, I would like to do a 2jz swap. Money will be tight unless I can find a 2jz for a decent price or I sell the 7m motor. I know there is a lot of information of these swaps. Now Listen I have looked at MANY Threads. There is good information, but...

Well, for now I have a lot of things to do, so sadly I will be parting out the " Teal Supra " I am saving for a MKIV because I just want a nice 2jz and it's not worth my time throwing it into a mkiii. All the parts off this car are here minus like the drive shaft, radiator, and two inter...

Alright, I may be making a bad decision, but I may go with a 2jz into my car. This car will be sitting for a long time now but I really want the 2jz in there so yeah I think I am going to go with it. i will be selling my '92 NEW ( from TOYOTA ) Wiring Harness last one produced. Any...

Is there a metric chart or US Chart of fittings sizes I will need the metric for the supra, but when I do the fuel cell there is already US fitting on those alright thanks.

Alright. I have 4 gauges to install and I want to make sure I am placing them in the correct place. Well here is what I have: Water temp Oil Temp Fuel pressure Boost Water temp should I put that in place of the BVSV? I have a fuel cell and no longer will use the BVSV anymore, plus it...

Well I got a set of 5 gauges.. Oil Temp Tach Fuel pressure Boost Pressure ======> Came with sensors for each one. Water temp I got the controller box and I am goign to test these and make sure they're in good condition. They're very nice, and I am only missing I think two gauges...

Okay everyone. I have this gap with my drive shaft could I have a 1jz bell housing? or nope.. I am not sure so.. please!! No yelling at me.. what is the difference isn't it like 20mm or cm? Also are the engine to transmission mounts different for auto trans and manual trans I can get...

I won this on Ebay for 52.00 They sell a bunch of these with NO* BUY IT NOW"S. I want to custom fab this for my 7m-gte. Was this a good price I paid with shipping $98.00 So let me know thanks!! Check the link here...

Okay well I was on Xceedspeed.com and I saw the add for 5 Gauges, and they're were Defi's, TACH< Oil Temp, Water temp, Boost, and Fuel pressure, they're all used minus the oil temp. I bought all of these with the controller box and all the wiring for $200.00, I may use them I am not sure but a...