Search results

Does the decel air setting on first gen safc aid in helping car to not stall with open bov on afm setup? If so can someone please help me get it set up right? Car doesnt stall all the time but will on occasion and wanna fix it. I am in the process of getting a recirc tip but that has to wait due...

Ok so i took the car out stayed out of boost most of the time, just a few little 3rd gear pulls. Got home found that overflow has not overfilled but raised about an inch or so. First thought BHG:( I checked oil, good. Pulled plugs, Good. The temp gauge never got out of the optimal range, factory...

My mods are: Dm 57 trim turbo, Walbro 255 , Denso 560cc, Lex Afm, Dm ic kit, LC1 wideband ,Aem truboost, 3 in turbo back, Apexi safc Did about 8 runs (140 bucks) Baseline with no fuel out and stock boost was 271/280 only went up from there. Most of the runs were boost adjust only no safc...

I finally got the last piece of my puzzle (dm ic kit) Car is done need some help on the initial tune. My mods are: Dm 57 trim turbo, denso 560's, lex afm, apexi safc, aem tru-boost, lc-1 wideband, full 3" turbo back exhaust, Walbro 255lph, afpr w/jtube bypass and fpd bypass. driving at 6600...

I have been searching but not finding anything. I have an aem tru boost controller installed, and getting quite confused on how to program it and get my settings correct without messing something up. I have been reading all the instructions but i am being thrown off by the "duty cycle" 10-90%...

Ok so for the first time in over a year the junkyard got a supra in there!!!!! It was an 88 7mgte, figured i would take a look and see what if anything would work on my 89. Mainly exterior/interior stuff. Well i found out the hard way, that there is not much. tailights too small. damn. Mirrors...

Ok so i am having bad luck with stock mirrors. They keep breaking on the housing, tried to add epoxy, prior to install of new mirrors and still end up being a weak point. Does anyone know where i can find some aftermarket mirrors, do not have to be electric. I know i can get them from toyota but...

Ok so i got a second hand manual boost controller, turbosmart. I am not quite sure how to run the vacuum lines? The controller has two ports, one that has an arrow that point inward. Is that from the wastegate, or charge side of turbo? Also there is another "T" that has an arrow says face toward...

I tried searching but not getting anywhere. is the turbo oil supply/drain gasket reusable? I heard awhile back it is and its not? Not sure if my dm turbo is gonna come with gaskets or not. let me know thanks in advance

Ok so parts are on the way, thanks to driftmotion and sm classifieds, thanks guys. I have a stock 7mgte that i am upgrading. I am currently running a stock hg with arp studs will i run into any issues up to 400 hp? I am going to be installing a 57trim ct26, manual boost controller (for...

I have a completely stripped 7m that i plan on rebuilding soon when funds are available, (an all power engine) But i have lost, or used most of the bolts, for the running 7m. My question, does anyone carry a complete 7m engine bolt kit? By complete i mean everything except main bolts and...

Ok so i just installed my used Apexi safc (oldsking) I have everythign properly wired i just have not connected it the afm connector yet. Everything does work on it, rpm and throttle position. I am wondering what base setting would be good for a stock 7m at 6600 ft (colorado) Or should i just...

Tried searching but cannot find anything. Ok so i am curious as to what injectors (make, model of car, and injector size cc) will drop in on the 7m, fuel rail and mani. with the exception of new clips. I know the rx7 turbo 2 is one. Along with all the sets sold from the vendors. I heard...

This has been buggine me for sometime now, tried searching everywhere for this. I have a random connector just chillin out next to the hazard swith in the small little horizontal opening, which i believe should have some sort of switch or cover on it? It is a factory connector, and i have...

So i am wondering if anyone has ever done a gm or any other brand mass air flow sensor on the 7m? I know that using a map is more of a guess, as compared to afm. so let me know if it is possible, if so how i would like to clean up my engine bay from the afm housing but still have an accurate...

I am thinking about gettin this kit, just wondering if anyone has personal experience with it? On what mods also?

buddy is doing a rebuild on his supra (no net or he would be on asking himself) what are the ar tolerances for mhg, believe he has a titan motorsports 1.4mm mhg I think his head gasket may be a little to small, but needs some specs the search isnt helping right now

I had a few questions about all the other info that is on the door jamb label. I can decode the vin, not concerned with that. more curious about the very last few lines, after all the shit about conforming to federal standards. What i am wondering about is what the c/tr, a/tm, model numbers...

Ok so right now i have a stock 7mgte in my 89 supra, and i need advice on which way to go with it for performance. i have a cap of about 3500 dollars. My first thoughts were standalone system, bigger turbo, fuel supply, exhaust, clutch etc.... then professional tuning. Got some advice on that...

I am planning on purchasing alot of stuff for the supra. (aem ems, 550 injectors, fuel pump, afpr, turbo upgrade, clutch, exhaust) Was wondering what all i needed for the ems itself. I know that i will need the map sensor and pigtail, along with the iat and pigtail, plus a wideband set-up. I am...