Search results

I was wondering how many people have bothered to rebuild their jz power steering pump? Mine is taking a shit and thought about rebuilding it. Any one have any input on this? I might just go get a new one if it is too much of a PITA.

I am in need of some good tires. My rims are 245/45/17's I want to stretch them a bit to clear arches and am currently running Falken RT615's I want to get some new tires and want to move away from the Falkens. I live in the northwest and deal with alot of standing water and leaves. Car...

Ok I need a switched 12v supply to give power to the positive side of the COR relay, I am swapping a jzx90 ecu and harness. I grounded the cold side I just need a good key on 12v supply to give the circuit power. I am searching and I will keep looking just casting a broad net ---------- Post...

on the ing switch there is a brown and red wire with the label ST2. it terminates at the connector to the firewall body harness. I cannot seem to find it in the TEWD or by searching ST2* in this or on SF. any ideas?

I recently finished my 1j swap, I have a bunch of Junction Boxes from a different clip. I was wondering if I could recycle a J/B to house the relays for new systems such as Efan's relays , HID for light relays ECT. I just don't want a bunch of relays mounted all over the place,but rather a...

I have a Fluidyne ALM Radiator, It has the stock provisions for the Aux fans and the factory fan shroud. I have finished my 1J swap and will be running E fans. My question is. Will the Mishamoto twin fan set up with Aluminum Fan Shroud bolt up to my Fluidyne rad? If not does anyone have a...

I recently got my intercooler for the 1j. it is hitting the support for the latch and horns unless i put it in at an angle like stock. I would like to see some pictures of how others have mounted theirs. I suppose it dosen't matter either 7m with a ffim or a 1/2jz. I just want to see if people...

where does the wire that plugs into the Starter go, Not the one that bolts on but the other? I searched for ever. Either didn't search the right term or just didn't see it. BTW it is a Z30/X90 Auto Harness

I donated mine from my Supra it wont be on the road for a little bit and the person is hella poor . It went into her 89 Camry. Is there a way to check what was bad with it. I know it is shot I am just curious as to what went to shit . thanks

I am looking for a 12v supply to supply the ignitor, injectors,and sensors on my JZX90 harness. I also have a few wires left from the jzz30 ecu pinout and I am unsure what to do with them. the external load input stop light switch abs exhaust sensor thanks Matt

I am looking for the part numbers for the B1 B2 B3 and M1 engine side plugs . I sold my GTE harness with the motor and need them to finish body side of swap . thanks

I wanted to post this in the SME section but the subtopic is closed . I am currently extending a harness and would like to know the correct way to extend the shielded wires such as the Knock sensors etc. On the harness there is about three inches of "normal" wire on either end with a larger...

I recently deloomed and traced all the wires on my Jzx90 harness, The harness is from a 5spd I found out. I have 90% of the wires dealt with. I made the replacements for the eb1 and eb2 plugs by tracing the 7m side wires to their places and functions ( most of which are from the plugs missing...

I cannot find the eb1 or the eb2 plugs ....I know were they are "supposed to be" but the are not there. I have none of this? nothing on car side and nothing on harness side to indicate that it was cut? http://www.freewebs.com/1jz-gte/1jz%20issues%20002%20eb1%20eb2.jpg I am also missing the...

Were can you source a IAC from? I have the part number so I can orderit from Japan. Would a 2j IAC work or should I just bit the bullet and get one from the motherland?

I have a chaser harness that had some shattered and missing coil pack clips. I have a set that I am going to rewire in and I am unable to figure out what clip goes to what coil pack. So basically I need to know what the sequence is when I clip the coilpacks inI can grab a pick if needed...

Ok I was trying to be the bigger man in this situation . In 2006 I killed my NA 7m. I posted on the fourm asking about swaps and the normal newb questions. I was approached by 88suprafast1 ( http://www.supramania.com/forums/member.php?3172-88supraFAST1). He presented himself as a shop owner...

Besides the two large grey ecu plugs what are the other plugs and where can I get a pin out for them?

Hello Everyone, I am swapping in a 1j into my A70. I bought a JZX90 harness not knowing that it was only half of what the ECU needed. I should have researched better but lesson learned. I am in need of either a JZZ30 harness or the Body harness from a JZX90 . If anyone in AU can help me out...

Can I put a chaser motor set into my supra. I searched all last night on and off of the fourms and really havn't found much. I PM'ed Dr tweak and he hasnt gotten back to me yet. I am sure he will soon. Right now I have the motor, ecu and harness. I read that two of the ECU plugs are on the...