Search results

After 8 years I have decided to sell or part out my Supra. My Supra is driveable and very close to a condition where I would feel comfortable driving it daily. The car is an ongoing project however, so there are a good number of little things I would have wanted to finish/tweak. I just will...

I need to connect my oil pressure sender back up, however I do not have the OEM connector. Any recommendations? Should I just buy a pigtail for the connector from Toyota?

Ok, I know i'm not the only one with a Supra tattoo...Maybe... Any how, here's mine, who else has one?

I did some more work on my Supra in the past couple months. Today I dropped the engine/transmission so that I can finish fixing up my shifter hole. I found a great way to do it. Left the entire exhaust connected to the engine along with the transmission. I also left the engine connected to...

I crashed my 2001 R1 today. I'm still not really sure every detail about what went wrong. I was shifting into second a few hundred feet from a stop sign doing maybe 25mph. I think the transmission stayed in 1st and the bike gave me a real surprise when I let the clutch back out. The front end...

I have spent a decent amount of time researching this. Do any of the major road racing sanctioning bodies have any restrictions to removing unibody structure when installing a cage? I want to maximize room in the passenger compartment with say, a 6-point cage. One way I have thought to do...

It's pretty much official. I am moving and staying here in Grand Forks, ND over the summer and the following school year. I plan on moving my Supra here over the Spring break. Who here has a Supra?

I was thinking of what weight I could cut out off my Supra without reducing structural integrity much if at all. I figure I can remove substantial weight by just cutting it out. I would like some other opinions on removing the radiator support framed by the red line in the picture attached...

I have a fuel cell mounted in my trunk. I cut the floor of the trunk out and mounted the cell is basically the same spot as the stock fuel tank. Of course, I need some sheet metal to form a bit of a "firewall" between the cockpit and the fuel cell. I was thinking of doing something like in...

I have some large gaps in the hole of my trunk around the fuel cell I installed. I want to cover those holes up. What guage of sheet metal do you guys recommend? I was thinking 18Ga should be fine. Any idea on how to help seal up gap between the fuel cell and it's mounting frame? Maybe...

I have a 15 gallon ATL fuel cell in my Supra. It is not feasible for me to use a factory level sender. Looking at the TSRM, the resistance range for the stock sender is 4(+-1)-110(+-7.7)ohms. ATL does not sell a sender in that range. However ATL does sell a "GM" range sender. That sender...

I am looking for an electric fan setup for my LS6/T56 setup. I have a huge radiator. I don't remember the dimensions but it barely fits between both frame rails. It also barely fits from the top of the original radiator to the bottom of the front subframe and is 3" thick. I don't need any...

What is everyone doing about replacement bumper brackets? Are they still available from Toyota? Does anyone have a good solution to custom ones? I got a different bumper cover as my old one was crap. The brackets from both bumpers are in horrible condition. I am looking for an easy, cheap...

I have tried to bleed my clutch system on my LS6 setup. I have all of the air out of the system but I do not get very good pedal. I am beginning to think the master cylinder of the Supra is too small. Are there any direct swaps to larger master cylinders? Perhaps a Toyota truck/SUV?

I am wondering if anyone knows the thread size of the rack return fitting. I am looking to convert -6AN.

Who owns this car? I have an idea, but lets see who responds.

I have been wiring up my power windows. Here is the problem, when hooked up to a battery the driver's switch does not operate any window. I can however jump the correct wires coming off of the harness at the switch and operate the driver's window. I did some basic continuity testing on the...

Being that I am wiring up my entire car from scratch I need to get a couple positive feeds off of my ignition switch. It appears to be able to take quite a load, looks like about 10awg wiring going to it. However I did a search here and IJ seemed to indicate that the switch was not capable of...

I saw the red and blue posts.

I have the engine mounted up in my LS6 Supra. I now want to setup the brakes. I have removed all brake lines, ABS, proportioning valve etc. I will be putting in an adjustable proportioning valve on the rear circuit. I need to plumb up all of the calipers. I am wondering what you guys feel I...