Search results

So did any one keep their EGR during this swap? I want to keep mine but i am unsure of how to hook it because there are so many more vacuum lines for the 2jz EGR system than there are for the 7m. Any input would be appreciated.

If i put any kind of coupler or anything on my throttle body it will rest right on my turbo.. Dont really know how to remedy this i'm sure a hot turbo will make quick work of anything touching it. I tried two different turbos too, nothing crazy, mid sized turbos. Did any one else run into this...

Ok guys.. i have a compression problem with my 2jzge, every cylinder is ~40 psi with the exception of 1 being even less. I added oil to the cylinders and saw no change. So i pulled the head off, cant even tell if the head gasket was blown (i'v never ran the engine). Then i decided to check the...

Hey guys im currently working on putting a 2jz with 7m electronics in my 87 turbo. The first problem i ran into is i cant figure out this damn throttle body! Is this thing even possible to use in an mk3 with 7m electronics? i cant even get it to open more than 1/4 of the way, oh and theres the...

I thought i read somewhere that supras only came with metal sunroofs, so i cant figure out if this is factory or aftermarket. only reason i would think that it was factory is because it looks so well done, with the button molded into the head liner and what not. Ether way im sure you guys could...

Just bought a "rebuilt" engine(rebuilt my ass:icon_mad:), so i decided to look at some bearings. This is rod bearing #1 and #6 i was wondering what you guys think about these? Also i was suprised to see how well the crank looks. I think anyway..

i just installed a 57 trim ct26, now my car jumps between 350-500 rmps until it stalls. ran flawlessly before the new turbo. any idea whats up? I have checked for vaccum leaks and boost leaks. dont know what else to check. I have searched with no luck :(

Hey guess the time has come for me to get a new clutch setup. I don't know how much power i am making but its enough to make an almost new stock clutch slip. I have been reading a lot about clutch and i had a few questions. I read with an upgraded pressure plate you run the risk of crank walk...

I just installed a single filter oil cooler system like this one. http://www.supramania.com/forums/showthread.php?62838-Installing-a-Full-Flow-Thermostat-Controlled-Oil-Cooler-amp-Remote-Filter (Thanks jdub). now i have a oil pressure gauge i want to install. My question is, since i have extra...

Well my car came with a fluidyne radiator but it never built up any pressure. So I am thinking i need a new cap. my question is do i get a stock supra one or do i have to get a fluidyne one? I have done some searching but it didn't help any.

well i had a leaking had gasket i think from the day i got the engine back from the machinist. i was hoping you guys could tell me what the fuck is up with this thing? Any one know where it was leaking? and the part that confuses me is what the hell is with the metal to metal on the other side...

ya i know... "another one..." this one is different though! iv searched believe me. I was wondering what might cause a almost stock 7m to boost past one bar with no fuel cut? all it has is inter cooler hard pipes, blitz bov, Greddy boost gauge, Greddy profec ebc and a 3" Dp with the stock elbo...

i was just wondering if these were normal oil pressures for an engine with 1000 miles on it? some how i don't think so... one is at hot idle and one is at 3000 rpm hot. im sure you know witch is witch.

OK so im looking for a new turbo and i need it to be a pretty simple affair to put in. upon my searches i came across this "bolt in ct26 turbo". It clearly says that the factory oil and water lines fit perfectly but in the side by side picture you can see that one is different from each other...

hey guys i just got my rebuilt motor all installed and it has no spark :(. I was wondering if the cps had anything to do with not having ANY spark, or would it just screw up timing? This is my first ever foray into any serious engine work but i checked all the grounds and i am not sure what...

any one ever tried these? http://cgi.ebay.com/ebaymotors/Intake-Hardpipe-Supra-MK3-Turbo-Inlet-Pipe-7MGTE_W0QQcmdZViewItemQQhashZitem2c4f9af053QQitemZ190314115155QQptZMotorsQ5fCarQ5fTruckQ5fPartsQ5fAccessories i was just wondering if this would be a complete waist of money or if it...

ok guys i have had my supra for only like 2 months and it needs a new engine :3d_frown: but anyway i cant find a motor local so i was thinking about getting a JDM one. i know you guys don't really like them through the searching i have done but whatever. Here is the problem i see they have...

hey guys i was just wondering if there was any way to tell if i had a mhg or not? i thought i read some where that the only way to tell was to take the head off and look. but i started looking between my block and head and it looks a lot like metal. so is this thing i am seeing not even the...

i am removing my engine for a rebuild. i got every thing taken off i tried removing the engine and i cant seem to get the engine separated from the tranny. right now there is about an inch in between the block and the bell housing and the engine moves side to side but not out. it is a five...