Recent content by harley1985

  1. H

    na, im going back to stock. just a good ol turbo supra.

    na, im going back to stock. just a good ol turbo supra.
  2. H

    everything bro. nothing is lining up. im just going to sell everything and put it factory until...

    everything bro. nothing is lining up. im just going to sell everything and put it factory until i have the money to start over again. fixin to post all of it.
  3. H

    know how to hook up a wideband and apexi safc?

    know how to hook up a wideband and apexi safc?
  4. H

    R154 Throwout bearing/ clutch release issue *Video inside*

    sorry to hijack the thread, i put a spec PP with a 6 puck in my car and i seem to have a lot more play on my clutch pedal, i checked it before i put it in and it was exactly the same as the stocker. is this normal? the only real difference i saw was the 6 puck was about 1/8 slimmer than the...
  5. H

    quickie? alternator wire where does it go?

    thank you sir! thats wat i figured
  6. H

    quickie? alternator wire where does it go?

    the red 3 or 4 inch wire going from the back of the alternator? it goes into what looks to be a resistor or a huge diode? then continues to a eye connector? is a ground? (figure it is not b/c its red) or does it go to the top stud of the alternator (the 12V that goes to the battery) can someone...
  7. H

    one set of main bearings wider than others? (7mgte)

    well look at that, somehow i managed to put them in correctly without even knowing, im SO glad i wasted 2 hours pulling my crank shaft back out lol.... thanks anyways
  8. H

    one set of main bearings wider than others? (7mgte)

    hmm im fixin to pull it back apart and check. ill letcha know
  9. H

    cylinder walls already "scarring" (7mgte)

    one more for yall. i may be a little paranoid but i just put all new rings on my pistons and installed them. i checked my gap on every one of them and all were within acceptable range. i rotated the crank by hand a few times and already noticed some marks on my cylinder walls. i had the block...
  10. H

    one set of main bearings wider than others? (7mgte)

    kinda interesting though that it fit in the other main cap. hope i didnt damage it....
  11. H

    one set of main bearings wider than others? (7mgte)

    lol oh wow that was quick, thanks so much. now i gotta pull this fucker back out lol. thank you agian.
  12. H

    one set of main bearings wider than others? (7mgte)

    so... im going to go out on a limb here and say its the number one cap isnt it? i just measured it and its exactly 1/8 bigger than the other caps.
  13. H

    one set of main bearings wider than others? (7mgte)

    so i got my rebuild kit in and put new mains and thrusts in and slapped in the crank shaft in. now that i am looking at the old mains i realize that there is one set of mains that are bigger (wider) than the other sets. i guess i was not paying attention or something, but i imagine that its...
  14. H

    bad egr?

    ahh i c. ok well if the egr isnt working correctly would it not run very rich? possibly causing pre det? which in turn would ping the knock sensors which in turn would mess with the timing? am i barking up the right tree? idk man. please enlighten me. its so frustrating. ive checked and checked...
  15. H

    bad egr?

    double and triple checked for boost leak. spent 100 bucks alone at the yota dealership in new hoses. its not loosing boost, i believe it is hitting fuel cut b/c of the egr is shot and its running super rich. the only thing i have to reference off of when it does it is my boost gauge. idk, its...