Search results

Whats up guys Ive been researching my 2JZ MK3 swap and have almost everything gathered. Alot of you guys have done this swap successfully so Im curious to know what differentials you went with? Should I get a 2J diff or should I build my stock rear end. My power goals are between 5-600whp. I...

What would cause low compression in cylinders 1 and 6. A friend of mine is having trouble with his account on here, so I'll ask the question for him. He did a cold compression test and here are the results: Cylinders: 1- 110 2- 155 3- 155 4- 155 5- 155 6- 110 What would cause this...

Here is my problem. I have a check engine light that comes on and off. When I am driving, and I get on the gas, the light will come on. When I come off the throttle, sometimes it goes away and sometimes it doesnt. I have been searching all day for the page on cygnus that shows what points to...

I'm looking to replace my throwout bearing, as mine is gone and making a hell of alot of noise. Is the OEM throwout bearing from Toyota good for 400-450rwhp? I've heard that they have a tendency to break and whatnot. Anyone here running 400rwhp with a stock Toyota throwout bearing? Thanks...

Hey guys, I've been looking around for a friend of mine who wants to do a twin walbro setup. He's currently running Wolf EMS for management & Precision 1000CC injectors... turbo: GT42. Bottom end: fully built, JE's+Eagles. Head: Stock, Transmission and clutch: Centerforce Stage 2 right now...

Hey guys, I don't ask much questions on the here because I hate asking stupidass questions, but I feel this one is important. I need a way to tune my car, because Im running too rich. Although rich is better than lean in any turbo car, theres got to be a certain point where rich is just too...

Is the stock 7M crank forged. I have a feeling it isn't, but I just want to be positive. Is the 1J crank forged? I know the 2J crank is. I have a friend attempting to run nitrous and he wants to know which are forged and whether or not a 1J or 2J crank will work in a 7M.

Driving to school this morning, I heard bubbling coming from under the hood. 2 minutes later I got to school.... I popped the hood and all the coolant was gushing out of the exh. mani. I recently did the HG, and I knew I messed up on one thing. My biggest mistake was not sending the block out...

I've had this problem for a while now. The trouble with my car was that it would start on and off. Sometimes the car would start first key. Sometimes she wouldn't start at all. I figured the coil pack was on its way out. About 2 weeks ago, she wouldnt start at all. I tested the igniter and the...

I went to Advance looking for Anti-Sieze grease. I didn't want those small packets thought. I asked for a tube. They gave me Dielectric grease. Would it be ok to use Dielectric grease on my exhaust manifold studs? I just helicoiled a stud and I'm putting it back together now. Just wondering if I...

I am having some trouble accelerating. I just put the motor back together after doing a MHG job. I got rid of the cruise control. After you remove the cruise control, what are you supposed to do with the cruise control cable? Is it supposed to be connected back to the rest of the throttle...

My oil pressure gauge wasn't working for quite a while so I never knew what my oil pressure was. Now I fixed it and it's getting me worried. What should my oil pressure be for a completely stock 7M. Stock turbo, Stock piping, Stock IC, Stock fuel injectors. Nothing has been tampered with.

My park lights and my cluster lights do not work. I checked all the plugs and grounds on the back of the cluster. I searched the forums and found a similar thread. The #2 post on this thread sparked me. I remembered that I left out a small connector on the engine harness because I couldn't find...

I just hooked back up my entire harness and I connected the battery cables, and my Fuel pump relay is clicking continuously. Is it shot? Thanks, Ryan

I'm putting my car back together and all the plugs on the harness are plugged back up except for the oil pressure sensor. Its the grey boot with the little square plug. Where does the square plug go? I can't figure it out. I don't seem to remember where it plugs. Does anyone have a picture of...

I've checked the TSRM for the sequence for torquing the head bolts, but I can't find it. Can someone help me out? I also searched the forums, but all I keep getting is BHG stories. =/ Thanks in advance, -Ryan

I'm having some real trouble with these studs because I don't know what to do. I have ARP Head Studs. My friend is telling me that you have to torque the studs into the block, then the head and washers, then the nut, and then you torque. I've read numerous threads on doing the HG, and I haven't...

I want to upgrade to a Lexus AFM and RC550's but right now I only have money to spend on the Lex. Would I gain anything upgrading my AFM and running my stock 440CC injectors? Would it cause me to run lean? I'm running a stock CT26@10psi. I don't want to get a Lex now, and it isn't beneficial at...

I was just skimming through Craigslist, and I found this.. http://newyork.craigslist.org/jsy/car/366690718.html Definitly not worth more than 7K in my eyes, but this guy wants a chunk more.

I'm doing my headgasket, and I wanted to know if it's possible to do a head gasket using ARP head studs while leaving the block in the car. Im hearing that you have to pull the block out to use ARP's. Has anyone done it with the block in the car? Lmk. If I have to take the block out, I won't be...