Search results

FYI we used a gates hose it was on amazon so free shipping in two days. same bends as original. it was a pain to get the original off I had the clamp closer to the engine had to cut up my arm with a snub ratchet to get to the nut. I flipped it around when I put it back on and had my son with...

Thanks helpful info. I wish we had changed it when we had the engine pulled.

The heater hose that returns to the engine from the car has started to leak. 7mge car, question is can you still get the prebent / formed hose from Toyota or any body else? Or do people just use what ever size it is of universal? I am not sure how to get the connection undone on the back of...

Car is fixed injectors replaced

the noid connector confirmed that I am getting a ground pulse to #5. I pulled #6 to compare it to a good circuit. I noticed the engine did not run any worse. the pulse was the same. unfortunately it means that cylinder 5 and 6 are not working. I verified that get spark and they are getting...

The noid light should confirm this or confirm I fixed the wiring. Either way I want the car done so my son can drive this has gone on long enough.

We got the new connectors and put one on number 5. No change. Hyvman I have direct wired the injectors on 5th cylinder to verify it is squirting gas. I think at this point I will ensure we have good compression. 180 plus I will then try to jumper directly from 3 to 5. There is not enough...

update we checked compression and it is good not the issue. We removed the fuel rail and replaced the injector on #5 cylinder. We replaced the rest of the connectors going to the injectors put it all back together and we have the same issue number 5 is dead. I pull the spark plug wire and no...

We go the new connectors and put one on number 5. No change. Hyvman I have direct wired the injectors on 5th cylinder to verify it is squirting gas. I think at this point I will ensure we have good compression. I will then try to jumper directly from 3 to 5. There is not enough length to...

I don't think the head gasket is bad. This engine is a jdm with a new headgasket. I checked the torque when I got. We have re sealed the engine and put in a new oil pump. If the connectors don't do anything I will check the compression. If it happens to be bad I will scream but then use my...

We have continuity on both after we replaced the section of wire. But still 5 is not working. That is the real head scratcher. I am a little more confused now that my reading for a na are that of a turbo.

I don't know how he got 18 before I do know that the digital meter I had broke and the old analog he used was giving him 10 -12. I picked up a new cheap meter and it gave me the readings below. 5 was different but not by much We put on a new O2 sensor and it improved how the car runs under...

I will check for fuel on the plug. Would this mean it is over squirting?

I have not swapped around injectors. The injectors were cleaned and I tested them before putting them in. If I can get fuel to go into the cylinder by connecting it directly to ground it works right?

Ok I put this in the wrong section my bad. I checked all injectors before putting them into the engine. All new seals. I can pull the plug wire off of 5 and the car does not change how it runs. When I pull the plug on the rest of the cylinders the car misses more. I confirmed number 5 cylinder...

I have a non turbo

the problem The car is missing, #5 injector does not inject gas. I have checked spark its good. engine fault code was 25. I have verified all other cylinders work. I have verified I have 12volts between red wire and ground with ignition on. on injector #5. we did not get connectivity between...

so your saying it will be a pain. thanks for the help. I let you know how the test drive goes then the repair work.

Sorry and thanks for the reply. I did not respond yesterday I had no power at home due to a storm ( 6 hours in the stone age because my phone was dead too). So now I know what I am looking at. I was hoping to not remove the pan. when I remove the pan will that be it? I mean will I be able to...

I purchased my na for 700. 300 later it runs. Body is rust free has good interior. If clean I would offer 2k at best then do engine swap. The bearings will go out unless you change them.