Just installed GEN2 and no rev but will idle understand this is kinda like the MAFT but more refined and a digital screened unit instead of dials,so i set up points through the unit like lo, mid,high also have the in and out for afm set 3.5 gm in supra out cylinder select 6 blah blah...
Silicone intake systems are well priced and have 4 layer silicone couplers and t bolts and whatever you need..Google the name of the company hope this helps
I have a GT-45 t-4 search ebayfor (gt-45) brazil made unit.....In my opinion it is a fast spool around 3500 full boost 28psi daily driven it gets quite angry 4000 to 7800 clip on rpm thru all gears dynoed at battleground got 588 hp 632 tq on pump gas 93 oct
Specs if i remember are...
Heres mine a 7mgte w/forged everything and a GT45 t-4
These were from original fab up in car before it ran,willtake some current ones soon.
Thanks to all you guys for do's and dont's it made life on this build so much easier.Got almost 4,000 miles on it so far and am lovin every minute of...
I just ran into a clacking noise also mine ended up being the camshaft caps being worn out my caps were hurt when the pressed on ring for the oil pump drive was pushed off due to a bad crank thrust washer....Pull the valve covers and use a long flathead screwdriver to pull and push around the...
I finally have gotten her on the road and no troubles so far except for a small leak on a heater hose and my oil feed line blowing out on the DYNO.....After a mild break in we bossted her up to 15 psi and got an impressive set of numbers.......518 hp 488 tq....The power master spools full at...
I cut my bumper support out but left a small strip at the top to at least try and keep its integrity....I have a 32 x 14 x 4 intercooler with a oilcooler reloc attached to it...I used little self tappers to attach it with no core damage.... The small piece just comes up to the top of the...
Finally got the intake and turbo housing back from powder.They are a candy transperant red with silver flake under the red....
I really think it set the engine bay off......
These are a couple of pics of mine i fabbed up to use the q45 tb and 3.25 thickwall alum tubing...Just got them back from powder today and have not had time for these pics but will post tomorrow...
I agree also with jetjock completely,and i am a driveline builder for 16 years and always use Rotella 15-40 after break in with nd 30.....The way i see it if my dads 47 pieces of equipment run this oil which is special for diesels(If its good in extreme applications then wtfn for a turbo car)...
Hate to say it but the turbo seals are starting to take a shit....Find out the answer and just pull the lower intercooler line off at the turbo and wallah oil or not....If not you need to do a good intake cleaning on it,there may be oil built up in the grooves of the accordian hose,and it sucks...
Go around to some shops in your area and see if they have a dead compressor tank or two laying around they would junk,or even the huge compressed nitrogen tanks(like 80 gallon)with multiple in's and out's...I have an 80 and 100 run consecutivly togethor and no more problem with supply and since...
I was in toyko for two weeks a few months back and rhd is ftw that shit was bad ass....got to drive the freeways and went to imperial palace and several other places of course had to see the sites from the goverment building downtown and rupungi late at night....F&F3 was cool cause i actually...
Got my wheels today they are ruff racing 277's 18 x 8.5 35mm off front and 18 x 9.5 35mm off rear this is a pic of the rear the other is at the shop will try to post a few more soon....
these fit perfectly for those who ask..fronts are 1/2 to 3/4 inside well and rears are the same so...
Afew more of the beginings of body work and the cold side mod to get this GT45 to fed the appetite that the 7m has for boost.
This shows the idea of placement to fed the giant.
Shows the 3 in outlet neck welded up waiting for repowdering.
Finally the begining of body work with...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.