Search results

Ok I got my head back from the shop a few days ago. They left the valve stem seals in and for the life of me I cannot remove them. I've been fighting them for a few hours with needle nose vise grips to no avail. Any tips or tricks to doing this?

Ok I found this thread http://www.supramania.com/forums/showthread.php?46690-SAFC-Wiring-Diagram-for-89-92-Supra-NA-and-Cressida for installing it. I've drawn out the pins so I know which wires to splice but what I can't figure out is that the ECU pins list two rpm signals and only one ground...

Ok I just bought an '89 N/A after being supra-less for almost 4 years. It's supposed to use the High Impendance green injectors however the moronic kid put low impedance yellows in it. Needless to say it ran like crap till I got it home. I had a set of 2JZGE injectors laying around which are...

Ok I did the a340e to w58 swap and the tach doesn't work now. I'm assuming it was driven off of the automatic. Is there an easy way to fix this? This is for a Cressida and I know it isn't a supra but the drivetrain was pulled from an 89 N/A MK3 so don't flame me :biglaugh: .

I got a new Holset H1E and i'm trying to figure out how to identify the A/R. Anyone know how?

http://www.autosportlabs.net/Megajolt_Lite_Jr. Will this work with 7MGE electronics on a 2JZ NA-T swap?

Ok i've finally finished my 5spd. swap but it won't start. At first I assumed it was the neutral safety switch i bypassed (wouldn't turn over, starter didn't click) but that turned out to be leaving the anti theft box under the dash unplugged:3d_frown:) Now it clicks but still doesn't want to...

I bought a yellow 87 supra almost 2 years ago for 300 as a parts car. No title didnt think anything of it. Today cops show up at my house with a lady and a title for the car. It's still here but damn it's been here almost 2 years and she wants it now?! Is there anything I can do because i was...

Well the cable is broken at the little metal 90 bend that screws into the tranny. If i leave it unplugged will the gear oil leak out of the hole?

A340E to W58. I bought a clutch kit and it came with 1 big clip for the throwout bearing/fork. The TSRM shows two small clips holding them together and for the life of me I can't seem to figure out how this single clip holds them together.

I may have goofed up. I put assembly lube on both sides of the bearings on the mains. When searching the tsrm for torque specs, it says only put it on the rotating side and not the back. Should I start back over or is there any real harm in doing this?

My 2jz is going to the machinist friday. My friends say it'll need rebalancing because i'm going to use a w58 (came with an automatic). Is this true?

Ok i'm trying to remove the old rings on some 2jz piston and they are stuck. I've tried soaking them in penetrating oil for hours with no luck. They are stuck fully compressed and it's pretty hard to fit a small pic in to seperate them. (i've broken 3 pics so far). Any easy way to remove/break...

Sorry if i've posted in the wrong section but yesterday morning someone broke into my building and stole 2 turbos from me. All I know is they were driving a white supra. The turbos were a stock ct26 with a polished housing and a 60-1 upgraded ct26 with a 3sgte exhaust hausing still attached. If...

I've got a 60-1 CT26 i've been wanting to sell for a while now. Problem is it's for a 3SGTE. Figured i'd sell it faster with a 7M exhaust housing on it but for the life of me can't figure out how it comes apart. Has anyone ever tried this before? Sorry my camera sucks.

How do you tell which cam is the intake side and exhaust side?

Will a crank position sensor from a 1jzgte bolt on to a 2jzge? Any help would be appreciated.

I read this on wikipedia: Is this true and if so what exactly does it mean? I have a 1jz head and a 2jzge block I had hoped to use.

I just bought a 2JZGE. My origional plan was to turbo it and run 7MGTE electronics however my friend just gave me a 1J head and intake manifold. Can I still make the 7M electronics work with it or am I going to have to find a 1jz or 2jz wiring harness and ecu?

Ok just thought i'd show some pics of my winter project: I've got 4 runners welded in. I'm using 43mm throttle bodies off of the 4AGE Silvertop. Still far from done just thought i'd share. Two questions: 1. If I tap a port into 1 cylinder runner is that enough vacuum for the brake...