Search results

I have had to replace the ignitor in my car twice in the past week. Each time the car was running perfectly fine and just shuts off. I try to restart and it cranks over and acts like it wants to start but doesnt. Replace the ignitor with a good one and it starts right up. I tested both of the...

My car wont start, I pulled the codes and I have a code 14. Tried clearing it but it came back when I try to start it. Iv tried searching for info about code 14 but couldn't find much. Anyone know what could be causing this or how to get rid of it?

Im putting my car back together and I cant find where this plug in connects to. It is behind the glove box. Anyone know?

Im trying to get my car started after a full rebuild. Im getting fuel to the fuel rail, but the injectors are not firing. I started going down the troubleshooting list on the TSRM and I checked the fuel pressure relay and it failed. The TSRM said each prong should ohm out to 3 ohms each. I got...

I jumped fp and +b in the diag box with the key on and my fuel pump did not come on. I have checked the efi fuse and the wiring and it is all fine. Is this a sure sign of my fuel pump being bad?

Just finished putting my engine back all back together and I cant find where this plug goes. It comes up right beside the fuse box and comes from the body harness from the front driver inner fender. Any ideas? Its a 90 NA swapped to a turbo if it matters.

I tried to bend the tube to fit fit around manifold, but the actual dip stick wouldnt fit through the tight bends. What should I do?

I purchased an engine gasket set from driftmotion and I was reading somewhere that suggested not to use the exhaust manifold gasket from the set. I will be running a boss turbo, should I use the one that came with the set, order one from toyota or just get a felpro gasket? Here is a link to the...

Over the winter I did a full rebuild on my engine and now that I am heading home for the summer I am going to be putting my car back together. I have a few questions. Im going to be running a boss turbo and I am looking at getting an install kit from suprasport, but there are two options...

I am taking a C++ programming class for engineer students and was wondering if any one here has experience with it. I have a home work assignment im looking for help on. Any help is appreciated.

i would like to create a signature for my car that i am trying to sell. If any one could photoshop the background out of the first one and put somthing cool back there and use both photos to create a sig i would greatly appreciate it. Thanks, Jason

Long story short, I had my machinist completely rebuild my lower end and i got it back to reassemble it and found the rear main seal retainer cracked. So i purchased another off a board member. The gasket for the retainer got screwed up so my question is do i need to get the proper gasket or...

My engine is bored .20 over and i need to know what size bore of hg to get.

I need a new seal for my aftermarket moon roof/sun roof. Does anyone know where could get one?

It doesn't like to start. At first, the battery seemed to drain overnight and i have to jump it to start it. I would get in the car and no lights would light up on the dash, nothing. iv replaced the new battery with another new battery and it did the same thing. So, i replaced that battery with...

i was looking at buying some arp head studs and saw they have u cut studs and regular studs. What is the purpose of having an undercut stud? Which type should i get?

My block has previously been bored over .020 and im getting it honed. Should my machinist use a torque plate while honing the cylinders? Should he hot tank the block or should i ask him to sonic clean it? I have JE forged pistons and goin to get new rings, are there any certain ones i...

I was taking off my fuel rail when i found this wire that i cant seem to figure out where it goes. My guess is that its a ground for something, it is bolted to the fuel line. Does anyone know where this goes?

I just got my head machined, they took nine thousandths (.009) off and i gotta order a MHG and im not sure what size to order. The head is 115.91 mm.

I am trying to decide which rims to get. Right now i have the Ruff Racing 279 6 spoke wheels in Hyper Black. I cant decide if i wanna keep them or go with with some ADR or Stern wheels. So, does anybody know if theres any actual differences between the two? They look exactly alike and are...