Search results

Question- I am looking to sell my 88 turbo and don't really know what I could get for it. Anyone have any thoughts on what I could start at? See below for stuff thats been done. Keep in mind that the car is finished, but still needs to be taken in and tuned. Doesn't drive now, it runs way too...

I have been searching and haven't been able to find anything. I have venom 550's installed, which may be the problem to start with. I was driving down the road with the car running fine and all of the sudden while stopped at a light, the car suddenly starts pouring fuel out of the exhaust, I...

Ok, I hope someone can help with this. I took my car out of the garage after sitting for about the last year. I have venom injectors,walbro, bigger to4e turbo,.... and more. I wasn't even on the gas much and it started puffing out white smoke, pulled over and I have fuel dumping down my...

I am ordering a new engine harness for my car and don't know for sure what year my motor is. It's all together in the car, so I don't have it apart to look at the internals. I am somewhat sure it's an 88', but not posotive. Is there an engine ID tag anywhere on the motor? I have heard that there...

I have a 7mgte, and just for a little background: built lower end, mhg, BOSS TO$E 61, walbro, fpr, upgraded intercooler and piping, lex afm, alum. radiator, removed egr, elec. fans, 3.5" turbo back exhaust, safc2, aem truboost, wideband, etc.... I have basically just broke in the motor and am...

It is a Garrett turbo, could this be used on a built 7mgte? The numbers on it are: MDL-TV5101 P/N- R8929797 S/N- T6187B0603 Some other numbers on the intake side are: A/R .60, and M-24

how do I tell if my motor and harness is pre 89 or not? My car was originally non-turbo automatic, and I changed it to a manual turbo motor, but I do not remember the year of the motor and harness.

I know that this has been covered before, but I have to ask. I have an 88 7mgte, The car won't rev very far. I am using the lexus AFM, among many other upgrades. I am getting a code 31 which is AFM problems. I just replaced it with a brand new one from schucks. It was like $200-$30O!!! The...

I have an aem tru-boost controller that I have installed. I have it working, but I don't think that it is how it's supposed to be. Does anyone know what to set the spring rate at? I did some research on here for it but came up with nothing that helps. Also, I have a Boss TO4E 61 ball bearing turbo.

anyone know a good place to go in western washington to get my supra tuned, somewhere good with supras or at least imports? I have a lot of money in my car and would like to have someone that knows what they are doing. I have taken it to turbo tech. in tacoma before, and they did somewhat good...

I My car was n/a, then I swapped in the trubo motor. No my tach doesn't work. I know how to fix it with the resistors, but my question is: will the tach not working cause the dyno to be unable to get an accurate rpm reading? I took my car to the dyno to get tuned, and they said they were unable...

I am just finishing up my build and was wondering what horsepower I should expect. It will be tuned and dynoed afterward, but I am just curious. I have an 88' turbo 7mgte with: 60-1 ct26 3.5 in. turbo back exhaust (no-cat) walbro 255 550 cc. injectors lex afm safc II cooleze ceramic...

I have looked on here and found no real solutions. I have an 88' that used to be n/a but now converted to turbo. I have replaced the complete motor harness and put the turbo tach in, but it doesn't read accurate at all. For now I am just going off of the AFC II tach, but would like to fix the...

Ok, I searched and couldn't find anything that would help. I have an 88' turbo. I took it into the shop to have a 2.0 metal head gasket installed (not because it was blown, but because I wanted to). They put it on wrong the first time and didn't remove some of the rivets, so it leaked down the...