Search results

I am interested to know if anyone has figured out a better and shorter way to route boost line to boost gauge in pillar pod. I have looked at my firewall a couple of times and it looks as if there are no free openings. I believe the traditional way is to run the boost line under the dash, out...

Can anyone tell me what this connector connects to. The person that wired up my engine harness had the two wires next to each other connected to injector power and the lone wire connected to: two power wires going to the IAC connector, and then two more power wires running into the harness that...

A little about the setup, it is a motor, tranny, ecu, and harness not a front clip. I basically took a 7mge engine harness hacked it up and spliced it into the 1jz harness. Car starts up and runs great, however will not shut off when key moved to off position. I probably missed a wire but do not...

I know this topic has been talked about a lot, however this situation is a little different. First question what happens to the tems when drop springs are put on tems shocks. Does it make the tems useless or does it make the drop spring with tems shocks better. The reason I am asking this...

I know this topic has been talked about a lot, however this situation is a little different. First question what happens to the tems when drop springs are put on tems shocks. Does it make the tems useless or does it make the drop spring with tems shocks better. The reason I am asking this...

Like the title states I was wandering if I could just get my car started and maybe move it around with the 7mgte map sensor as I do not have a 1jz map sensor yet. Thanks for any replies. and yes I know it will not fit the 1jz plug but I was going to dremel the ridge off If need be.

I was just wandering if anyone has ever found anything to add to this diagram http://web.archive.org/web/200512271.../92Supra6.html (Top left, ECU Pin outs) Also what do I do with the ELS-Taillight on T5 and A/C control on T7 and STP- Stop Signal on T14 does anyone know what the 3...

I am in the process of doing a auto to manual conversion. does anyone know the colors for the two wires on the clutch pedal switch also does anyone know the colors of the two wires under the center counsel for the Neutral Safety Switch. Thanks for any help.

I have an auto car 87 7mgte converted to standard R154. my driveshaft is to short know. I am having a hard time finding a standard(R154) turbo driveshaft. I can get my hands on an 87 standard NA drive shaft! Is there any way I can use the NA driveshaft(I already know the spline...

I have an auto car 87 7mgte converted to standard R154. my driveshaft is to short know. I am having a hard time finding a standard(R154) turbo driveshaft. I can get my hands on an 87 standard NA drive shaft! Is there any way I can use the NA driveshaft(I already know the spline...

So I bought a 1jz swap from a guy that gave up on it, only thing is he wanted to put it in a 91-92 (Kouki) cressida. I however put it in an 87 7mgte supra. The problem lies with the wiring harness, when I bought it it was already lengthened. First question does anybody know who lengthens...

Need insight on what kind of electronics to buy to monitor 1JZ! I have almost rapped up my bid and I wanted to know what products people are running to control their 1J. I just have ported wastegates, custom y-pipe and downpipe, cat delete exhaust 3", driftmotion intercooler kit for stock...

1jz into 87 7mgte wiring question. So I have been looking at the 1jz Swap Bible and am a little confused at this point. Anyone know where I can get the yellow plug dash harness schematics? Anyone can give me a little guidance? I have motor, tranny, ecu not front clip anything I...

I have my 1jz motor out of the car and was wandering if I should use the hydro water pump with out the fan till it dies or should I just put the 2jzgte pump on that I have sitting in the box. If I should use the hydro pump what should I do with the lines that are supposed to run to the fan?

I am Working on Making custom wire harness for 1jz gte into 87 supra Turbo and possibly non turbo MKIII. I am able to get brand new connectors and pins. These are 3 connectors from the JZ harness that I need the opposite connector. 3 connectors from the 87T engine harness that I would need...