Search results

Hey dudes, I picked this up for my cressida, but before i swap over the carrier bearing i just wanted someone to verify if this is the proper driveshaft, I seem to be doubting myself and would like a second opinion and I couldn't think of a better place to go to.

I'll start off with my mods: 550cc Lex AFM Walboro AFPR Boost/Oil/Wideband Gauges I just resurfaced the head and installed a felpro headgasket Did a compression test, they came back very low .. 110-120 across the board I'm also using a digital compression tester, i havn't confirmed it's...

So a couple months back i pulled my head and accidentally removed the bolt above the turbo's oil return. I cranked her over today and to my surprise a stream of oil came out of that passage, unfortunately i misplaced the bolt that was blocking it and can't seem to find any information on it...

Since not only has this forum been a huge resource, and the fact that my cressida is based around the 7MGTE i figured this may be of interested to some of you. Big updates in the near future, www.donedreamin.net

Hey guys, I'm a little stumped confused, either way mod details - 550cc Lexus AFM Aeromotive AFPR Walboro 57 trim Anyways i'm doing some test runs and i'm leaning out, i bumped my AFPR up and it corrected it a bit but i've got good numbers up till 3-4k than it starts to lean out...

Hey guys, i'm wiring up my SAFC NEO to a switch; just wanted to confirm which power power i use for the switch. I'm assuming the red/white wire to the switch and the red wire to constant 12V If anyone could verify this would be much appreciated!

Hey guys, Could anyone send me a picture of the connectors near the ECU of a pre88 yellow engine harness, Much appreciated!

I picked this kit up from Aaron and unfortunately crushed a portion of the line, in tale causing a leak. http://store.driftmotion.com/static/i-7mfueldampenerbypasshose.php Does anyone know the AN fittings on the line, unfortunately i dont have access to my car but have some downtime to get...

Hey guys, Just wanted to confirm which is outlet(to filter) and which is inlet(from oil cooler) Cheers! http://i257.photobucket.com/albums/hh211/xTeamclassic/photo.jpg?t=1329932915 Another question while im at it, anyone have a a close up photos of the pcv piping coming off the...

Hey guys, Was wondering if anyone has a photo laying around of these lines? http://www.cygnusx1.net/Media/Supra/Library/EPC/Figures/MA9047B.gif From the turbo to the block, and the turbo to the thermostat housing. any help is much appreciated!

Hey guys, This is my first overhaul i've done, just have a couple quicks questions, any pointers greatly appreciated! Whats the difference between grey plug vs yellow plug engine wiring? I'm reusing a hks mhg, going to remove all existing viton and apply copper spray, but how exactly do i...

Hey guys, i just picked up a mint jdm 7mgte, but the buyer before had the intention of building the motor and mid-way through gave up on the project. Nonetheless the motor was mostly together besides the removal of the oil pan. Now the motor was covered up but had sat in a shop for a couple...

Hey , I'm re-torquing my headgasket today (arp studs/metal headgasket) was wondering what sequence i should go abouts doing it . Thankss , much appreciated

Hey guys, i just want to confirm exactly which wires go where . having trouble finding any information online! thanks alot! ---------- Post added at 07:32 PM ---------- Previous post was at 07:29 PM ---------- I currently have it setup as : black - EQ1 power ground red - +B EFI main relay...

Heyy, Just swapped a 7mgte into a x73 Cressida , oil light is always on ; there is pressure . I'm using a 5m oil pan and pump . Any solution to this problem , I also do not have my oil cooler hooked up .

Heyyy , Just wanted some advice on how to run my EGR , i'm missing the piece listed below and im having difficulty deciding how to route my lines as its rather difficult to determine where each line is going from the piece im missing. http://oldschool.supracentral.com/repair/vac-hose2.gif...

Hey guys, Does anyone have a schematic or diagram as to where the turbo pressure sensor assembly is located, harness and vacuum line. little stumped, any help is appreciated

Hey guys, I threw a 7MGTE into a cressida. Was wondering how i should run my vacuum, last resort is capping it. I do not have VSV nor canister. One line running a T and splitting off to EGR unit and fuel pressure regulator. Other line running to BVSV and than to Heater control valve ->

Hey , i just want to confirm what these two inputs (sensors) are on the block.