Search results

What steel are you going to use for the sleeves? I'd be willing to pay a wee bit more for 316L rather than plain ol' carbon steel. I'm most likely in. Asterix

I find http://www.pegasusautoracing.com/ has very good service and good products. Asterix

What durometer is your polyurethane? Asterix

A photo of my installation. Sorry it's a bit fuzzy; I'll take another tonight with my hands braced. The hose is Aeroquip 3/8" for socketless fittings. There are two 45° socketless to AN fittings on one end of each; the other end is just crammed an inch or so onto the hard pipe and secured...

That loop is was a gift from Toyota so we could easily add a real filter and/or cooler to the system. http://www.supramania.com/forums/showthread.php?t=38486 If you don't want a real filter, go ahead a pull it out. Asterix

The hard line loop that goes up to the front bumper is the perfect place to add a filter. Get a remote filter base, hose, and some fittings, and plumb it in. I used stainless steel sheet metal screws to hold the filter bracket to the inside of the front bumper. I've had one for many years, so...

To move the spacer back out, just use a piece of 1/2" all-thread, two nuts, and two washers as a spreader. You can get tons of force with little wrench effort that way. Don't cut it, and don't forget to put it back in or you'll break your spindle. Asterix

See this thread for my post, also copied here: One washer under the head, two washers under the nut. Lots of extras... Asterix

Putting ends on teflon hose is rather harder than your run-of-the-mill rubber oil hose. The hose is much more difficult to work with. Pegasus has 36" pre-made hoses for $20. If you need that extra 4", they may make custom ones. If you do want to assemble your own, Pegasus sells a flaring mandrel...

Point taken. :icon_razz In my experience, RTV is good because it sticks well, but not so well that you can't remove it. It may take a little work with a credit card, but it does come off relatively easily. It's not like I epoxied the lights on. It'll last easily as long as a gasket. When I...

The plug under the spare closest to the front of the car can be left out. Mine hasn't been in the car for many years. The gas tank shields it from underneath so water never comes in from splashing. That way water never collected in my spare tire well. Fixing the tail light seals will cost you...

The space available is fairly thin. I ended up taking 2 large adjustable wrenches and grinding them thin. I can check when I get home how thin I had to make them, but it's probably around 3/8". That's what those special wrench adapters get you. You'll see how large they are when your parts show...

Dunlop SP Sport 5000 Asymmetrical They're quiet, not too expensive, do light snow just fine, don't get hard when it's cold, and last decently. Good traction for me. I've run through Toyo, Pirelli, and Yokohama through the years, and like the Dunlops the best. Wet traction is almost as good as...

Check the rating on your hose for the high pressure side. The pump can put out over 1500psi. Asterix

The hub is pressed in. That's why the instructions show using a puller to push it out first (page FA-10). You may be able to push it out, if you can fit your puller in there, but you'll never get it back in without a press. Just take the knuckle off the car; it's not hard. Then, take the next...

Ignorant mechanics will say you can't turn drilled or slotted rotors. It's not true. They turn like any other rotor. Asterix

None of that stuff is necessary. Has anyone seen those wishbone springs on other cars? I've run without any shims for years with no problems. The piston can ride just fine directly on the pad. Squeal is far more dependent on pad material than anything else. The shims and goo are just insurance...

Pegasus does not sell SAE bolts for good reason. AN bolts are specified by the unthreaded length and go by odd 1/8ths. That's why you can't find 1-1/4. The overall length of the AN6-12A is 1-5/16". I used: AN6-12A bolts at $0.69 ea MS21042-6 nuts at $0.79 ea AN960-616L washers at $2.99 for...

Pegasus has a nice selection of AN hardware. Use the AN960 washers and the MS21042 jet nuts. I'll look up what length bolt to use when I get home. One washer under the head and two under the nut does it just fine. What you do not want is the threads of the bolt in the joint. The smooth shaft of...

It is very pretty and will look pretty in your engine bay. Otherwise, it's a sham. It's hard to tell what's in it, but it looks like 5 capacitors. Whoo-de-doo. Asterix