Search results

Just picked up a mkiv and wanted to take the maft pro out of my mk3 and install it in the mkiv. I just wanted to confirm first though that it will work. I think it could because I see mkiv guys running map ecu's and i know a few mk3 guys are as well. With that in mind the maft pro wiring is...

Hi everyone. My supra was broken into last year, and the ignition tumbler was destroyed. I wanted to know if it were possible to get another ignition tumbler, and have a locksmith make it work with my original key. If this is possible, anyone know any good places to send it out to get...

How can you tell the difference by actually looking at it? I need to replace my gte pump and I have a link for an oil pump but I am unsure whether it is for a ge or a gte. Any help would be appreciated.

Alright guys, got another weird oil pressure issue. My last low oil pressure issue was resolved by replacing the broken oil pump drive shaft. 1000km later, the oil pressure has been good, but has since started to drop recently within the last few days. Only thing I did was install 720cc...

Went to the dyno the other day for the first time. I just did 3 base pulls to see what the car would do. The setup is a follows. gt76 x trim dbb turbo (6.5-6.8psi) 4inch downpipe, 3inch catback, 3inch catalytic with a 4inch center section. The 3inch reducer on one end of the cat sits...

Hi guys, I am running version 4.80 software and I just had a question that someone will hopefully answer. When using the pt tracking, it says to disconnect the o2 sensor. Now when that is done, the car is in open loop. I set the tps voltage at .45 (mine is .42 at idle) idle rpm at 800 a/f...

Went to the dyno the other day for the first time. I just did 3 base pulls to see what the car would do. The setup is a follows. gt76 x trim dbb turbo (6.5-6.8psi) 4inch downpipe, 3inch catback, 3inch catalytic with a 4inch center section. The 3inch reducer on one end of the cat sits...

anyone know the part # for the gasket that sits behind the timing belt case? Its pictured here. http://www.cygnusx1.net/Supra/Library/TSRM/MK3/manual.aspx?S=EM&P=63 I got the part # 11312 no.1 11312 no.2 I'm not sure if thats correct because i only though it was 1 gasket. Secondly...

I was fixing a few things today on my car, and I pulled off the timing cover. Now the first thing i noticed was that the timing belt was not riding properly on the oil pump pulley. It was partially off. When i removed the timing belt, the oil pump pull moves in and out of the motor, but not up...

just got my car back on the road. Now i'm running a ffim with a q45tb, tps adapter kit to work with the 7m tps. Now when i pull off, as soon as it his 1500rpm to around 2000 the car feels like it just stops and if i floor it, it bucks a little and clears up. It happens around 1500rpm. No...

Well juts the other day i noticed that my rpm gauge would bounce around, and if i got on the gas the car would studder sometimes. Well when i was driving today, the car stalled on the highway. I put it in gear to jump start it, no luck. Towed it home. Took off the timing cover and the...

Currently running a 4inch exhaust setup. i've been told its really deep and not loud at all compared to other 4inch mufflers, but it is really deep around 2500rpm, and sounds nice, not ricey, but i want something extremely quiet. my 4inch catback will be forsale including the muffler if...

I just noticed the other day, my right rear shock is leaking. Is this common when they start to go? It's weird, it just started out of no where. I thought it was an oil leak or something because the car was facing the opposite way the night before. The bottom of the shock is wet, and...

Well just yesterday i noticed a scraping noise coming from the timing belt area. When i pulled off the cover the belt was peeling. When i first installed it, the belt had a small rip in it, but i needed to drive the car asap, so i just installed the belt. The rip was extremely small...

Got a few questions that i need some input on. my motor was recently built, ross pistons, eagle rods, federal mogul bearings etc. now it developed a knock a couple of days ago, after roughly 3000 km. Before it blew I noticed that when i reved the car when it was warm the oil pressure...

just got finished building my motor. Now i have to fill up the rad once in a while. no visual coolant leaks. However, i took off the crank case going to the intake pipe and there is a little bit of coolant there. also, a little bit of junk under the oil cap. now this motor has 1200km on...

Hey guys, just finish my motor build, and i'm on the q45tb with the stock tps and a tps adapter. Now my problem is when i give the car gas slowly, around 1600rpm, the car bucks really bad and it seems like it just doesn't go anywhere, untill i press the gas even harder and it begins to move...

hey guys, i installed my defi gauges, but i wanted them to dim with the other gauges in the car. Anyone know what wire to tap into, on the dimmer switch to make this possible?

I need to know the torque specs of the engine mounts. anyone have this?

Here are some pics of the progress thus far. Still waiting to get back the driver side valve cover because the tps was in the way of the hose going to the block. I Had to get a 90 fitting pressed in, and my Machinist kinda scratched up the valve cover trying to do it.:icon_mad: Here are...