My 2JZGTE swap is largely completed. Car runs and drives well, but not running any boost from the Turbonetics GTK-850 yet. Base map tune on the EMS-6860 from DriftMotion. My guy (George) that did the swap said he found the "bandaid" relay fix on the old 7MGTE and removed it. He traced the...
I had this problem once...tried the relay idea and it worked, but I didn't like the way it looked. Decided the best fix was just to swap out the motor with a 2JZGTE. Problem solved!
Best,
Brad
At the bottom of the page I link below is what I think is the real deal HID projector retrofit for the MKIII Supra. 7"x6" rectangular Bi-Xenon.
The only problem is they are about $1000.00 a pair.
http://www.streetbeatcustoms.com/rectangle.html
Why don't you be the first here to buy a...
Something like these guys offer?
http://www.streetbeatcustoms.com/rectangle.html
Too bad they're so expensive...can it really be that hard to put a projector in a rectangular housing?
Brad
Thanks! I sure hope so!
No, the picture of the car on the lift is at BDJ's Racing here in DFW. It's a small fabrication shop. Brian is the owner and the guy that fabricated the exhaust system for me.
Sure would be nice to have my own lift, but I'm not sure one would fit well in my...
Thanks again for the compliments. Here is a shot of the 7MGTE before I had the ETS 4" intercooler w/polished stainless pipes installed.
Here is I think the only picture I have of the 7MGTE with the ETS system installed. Out of focus and a dirty engine, but it shows the different IC...
I considered the Tanabe because so many had posted good things about it and that the sound was much more subdued than most MKIII exhaust systems. I wanted the HKS dual tip exhaust system, but nobody had them and the used ones I found were pretty rough. It was then somebody suggested I have an...
Hello, Can't remember if we've spoken before, but noticed you're from Fort Worth...same here. Anyway, the reason for the post is to ask if your front left fender has two tree trunk sized dents in it or is that some sort of odd reflection in the photograph? Maybe we'll run across each other at...
That's what I'm leaning towards too. HKS must have made a change between the pre-89 and 98+ year model. That might explain why the black/black-white power wire mine came with looked a little out of place. Might have been a mid-production line change.
Best,
Brad
I do remember my HKS TEMS controller has that black/white stripe wire either zip tied or hot glued to the controller separate from the main harness. Mine is a 1989 7MGTE and I'm pretty sure I bought the HKS TEMS controller in either 1989 or 1990 direct from HKS USA. You've got me curious...
My HKS TEMS controller has a black wire with white stripe coming out of the controller itself. This wire is connected to a 12VDC ignition source. At the end of the HKS harness that plugs into the vehicle harness located at the passenger kick panel there is a solid black wire for ground.
You...
Hello,
Yes, the thought was to pipe this in-line on the low pressure side of the A/C system...so I think the pressure levels would be safe. This is also the side that is after the expansion valve...the A/C lines under the hood that are cold.
The condensation is a good point to consider...
Hello,
I'm considering a new intercooler and was curious if anyone has seen or knows anything about the S-Max intercoolers SupraSport.com offers?
I've put a call into S-Max, but so far haven't been able to get the right person on the phone. I'm hoping they'll be able to provide me more...
Ha! Same wheels here...
Planning on suspension upgrades to improve the stance a bit, but my TEMS has worked perfectly since new, the day I got the car back in 1989! So, I'm leaning towards the Eibach & Illumina II setup to keep the TEMS system with HKS controls intact...
Maybe, but when it happens it really sucks! Here are pictures of my fan clutch locking up resulting in the fan spinning so fast it sucked the shroud right off the radiator. This occurred around 5500-6000 RPM...
The fan, fan clutch and fan shroud were all a complete loss. I...
I'm considering selling my 7MGTE motor along with a few other items. I blew my head gasket a few days ago and I'm trying to decide if I should replace the head gasket or go forward with a 2JZ swap. I'm leaning towards the 2JZ swap because I think it will be easier for me to reach the HP...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.