Search results

Why does the j tube have just a pinhole in the one end? What is the purpose of this, and should it be drilled out if the car has any performance mods?

I tried to change my avatar to this pic,but failed at my attempt. This is the pic I want to use. Any help would be appreciated.

Has anyone posted any pics or vids of the few that did make it to Chi2K9? I have a few pics,but just from GLD on saturday.

So I'm at a buddies house earlier,and noticed on the cover of the April '09 Hot Rod magazine that there was a MK4 Supra back behind the cover car,a 1st gen Camaro.Check out the article,and sure enough,Toyota power in an iconic Detroit musclecar.IMO that's awesome.

I'm looking for a pass tail light,and the chrome trim from the front edge of the hood for a '84 Cressida(MX63). If any body is out junk yard hoppin',and comes across these,please let me know how much you could get them for.(shipped to 46514,or within 150 miles of South Bend,IN)

Can anybody please post pics of the MK3 undercarriage,front & rear looking straight up (car on lift.) I believe the haynes manuals had shots like these,if someone could scan and post them it would be greatly appreciated.

Quick question.My fuel pump went out in my one cressida.It's an '84,5MGE, and has an external pump factory.Will the walbro that everybody uses for the MK3's work?I can get the walbro for a bit less then what they want for a POS one from autozone/advance.If it will work,am I gonna need any...

Does any one know how much the stock connecting rods weigh?Curios as to how much heavier they are compared to eagle rods.

I'm pretty sure the fuel pump in my cressida is tits up(both fuses are good,wont run with the FP check connector jumped)Can the pump itself freeze?.Does anyone know if a 5M supra pump will work,the plug is the same?(cressida is 5M also)

Can someone who has pulled their subframes please post pics of how/where the spacers go (large rubber covered washers.)front and rear.My frames have been out of the car for a couple years,went to put them back in and have the feeling that I'm missing something.Might not be,just want to make sure.

I saw this a couple weeks ago and kinda liked it. Then Tanya posted this and I really liked it,followed the body lines a bit better and looked cleaner IMO. So tonight I decided to cut my stock hood up,got one side all roughed in tonight,gonna finish it up over the next few days. I...

I am planning on using the chevy valvesprings in my na.The big block chevy valvesprings come in sets of 16,meaning you have to get 2 sets and have 8 leftover springs right?Anybody have the 8 leftovers and want to sell,or planning on buying a set after new years and maybe want to split one set.

I have had a few headers for different na supras over the years.All of them have had the O2 sensor mounted in a tube that is a few inches long.Shouldn't the tip of the sensor protrude slightly into the actual exhaust stream to get a proper reading?

Exactly when did they change the crankshaft?How do you tell the difference?I bought a hard wrecked 88 for the engine,my 86.5 was knocking lightly.The 88 runs good,car has 110k on it,but the PO said the motor had been changed,and he thought it was from an 87.Pros and cons of the different cranks.

OK,I have an '84 Cressida,5mge.I have been having a weird starting problem with it.If the car is warm it starts good,but when you go to start it in the morning it cranks over for a good 30 seconds before it starts,but if it sits for more than a day it fires up as soon as you bump the key.It only...

Does anyone have a pic of a harness bar with harnesses installed in a mk3?

I have a problem w/my computer I was wondering if anyone could help me with. It's a Dell inspiron 9300.I have had it for 3 1/2 years.recently the screen started to fuck up,one minute it's fine,then you'll start to see thin lines come across the screen and it blurs out/shadow images stuff,but it...

does anyone know what this other tab is for? I know the one is for the sway bar,don't recall anything being connected to the other one though.

here's some updates on my rebuild.Got the doors and fenders hung,rear end is finished and ready to go back in,and the engine comp.is back together,motor is ready to go back together,but have to finish the front subframe before that can be dropped in.

Here are some pics of my mk3.Originally white w/dark blue int.Tore into the car at 170,000 miles(bhg,of course)Always wanted it to be black so a paintjob was in order while the motor was out.Started by shaving the moulding off of the doors/fenders/quarters,left the trim that seperates the...