Recent content by wardog

Well if you decide to upgrade i have a Full Bolt on Greddy 20g turbo kit complete for sale. Let me know PM me for more info

I can tell you from experience that Jdubs recommendations are right on the money. I have broken in 4 engines following his method and all have past the beating i have given them with a 60 trim and 3 ct26 60-1. I can tell you that 7 psi feels like stock on a 60-1 BUT its a different BEAST when...

Just pmed you I have 2 for sale...

Peytoncoyote--- You need to set up a goal for your car. If horsepower wise its around 400 rwhp you can just upgrade your turbo to a 58 trim, 60 trim or a 60-1. THis way you dont have to modify too many parts. WHATS YOUR CURRENT SET UP OR GOAL FOR YOUR CAR?????

If you gonna be running around 400 rwtq , my suggestion to you is Stock TOyota Oem Pressure plate $75 Ebay 6 puck $75 or if it makes you feel better Act 6 puck $150 Toyota Throw out bearing and pilot bearing I have used this in more than 10 cars making 400 + horsepower and always has hold the...

Damn those numbers are pretty low bad boost controller or not. I had almost the same mods but with 440s and i did a 15 psi pull and it dynoed 377 rwhp and over 400 + rwtq. But i had to back it down i was on the mid 12 AFR. Second run was at 11.5 psi and it made 355 rwhp and 377rwtq and it was...

It its defenately an exhaust leak more than likely on the manifold or downpipe gasket. Easy fix and the light ticking is the injectors, mine are loud too. Im concerned with the knocking noise i heard on the video at idle, it comes and goes. Take the car out for a drive 10-15 minute and come back...

Check the connector plug and harness to that injector. That cps sensor is not lined up, take it out and install it again. Search for CPS ALIGNMENT so you can see the picture in one of the post. Well you got some work cut out for you. Good luck and report your progress... :beer:

SUPRASTEVE You don t need to spend 400-500 dollars on a clutch for your needs. I have been using my STOCK TOYOTA PRESSURE PLATE , AND EBAY 6 PUCK DISK FOR OVER 2 YEARS. No problems or slipping what so ever at 430rwhp and 430 rwtq on a ct26-60 trim 550cc and 18psi ALL DAY EVERY DAY . So for your...

Hey that hose with the red arrow is the iac valve hose it goes to the intake accordion hose. The green one is a dealer item hose give a call to Jay marks toyota world in Houston, tx mention the supra discount to get a discount. Here is the number 800-327-2087. Good luck and if you have any...

Jordan first of all nice kills. I tell you what i had alot of fun with my 60-1 and i was limited to 11.5 psi. I dynoed 350 rwhp and 377rwtq at 11.5. So being at 14 psi with your 550s you should be right about 370-380 rwhp. That lil mazdaspeed 3 didn't have shit on your car. Dont worry about that...

Yeah what i do is i remove the nipple from the thermostat and run the heater full blast for 10 minutes. Never had a problem with air pockets in the system here in the beautiful texas heat.

A little more info on the oil pressure gauge set up would cleat out some questions? LIke what brand were is it hook up at etc etc?

I added a "T" vacuum fitting to the NIPPLE on the back of the manifold by the egr. I has been working fine and accurate as hell. I see alot of people adjusting percentages, Nah too much shit on those boost controllers. I LOVED my HKS EVC 4 till the head unit got stolen :-( , now the HKS EVC EZ...

In order to install an aftermarket oil pressure gauge u need an adapter were the stock sensor goes. Driftmotion sell a nice stainless steel braided adapter/extension for that aftermarket sensor. Good luck and maintenance on that Toyota is a MUST. By the way burning oil at IDLE 99.9% of the time...