Search results

  1. GreenChevelleSS

    Fuel filter inlet thread size

    going to be Replacing my fuel pump with a 340lph and decided to upgrade the fuel line to 3/8 while im there. I want to run a -6 an fitting into the filter from the pump. Can anyone tell me if its 14x1.5 or is it 12x1.25
  2. GreenChevelleSS

    2jzge runs bad.

    92 mk3 with 2jzge on 7mgte wiring and electronics evo 560cc injectors and det3 piggy, 2jzge vvti coils ebay header, s362 turbo, 3" exhaust. BC upgraded valve springs, GTE HG and arp studs. always runs like it has a misfire very lethargic, rough idle. i dont know how to really explain it, but...
  3. GreenChevelleSS

    hood blanket falling apart

    Just curious if anyone has any ideas on a a replacement hood blanket or someway to fix it. Its comings apart around the edges and looks horrible. I dont really want to just remove it either.
  4. GreenChevelleSS

    2jzge TPS with 7m ecu

    In the middle of a 2jzge swap into my 92, running the 7m wiring and ecu. Will the 2jzge TPS work with the 7m? I looked at the wiring and it shows the 2jz tps to have a vta2 instead of an idle switch. so that means 2 potentiometers in the tps instead of one and a switch
  5. GreenChevelleSS

    DET3 Fuel implant

    Has anyone tried the DET3 fuel implant mode on the 7m?
  6. GreenChevelleSS

    What changes at 2000-2500 rpm?

    Still trying to figure this crap out with my 2000-2500 rpm misfire. It happens no matter the throttle position. never missing below 2000 rpm and above 2500. It seems to do it more when the engine is cold, but still does it hot. Swapped the coil packs, ignitor, cps. Installed new plugs, wires...
  7. GreenChevelleSS

    cutting out and backfiring at 2200rpm

    Started having an issue where the car will cut out and back fire between 2000-2500 rpm. it happens in every gear no matter the throttle position. need advice on what to start trouble shooting. Ive checked codes and only have code 34 and know thats no the cause of this. Im pretty sure its...
  8. GreenChevelleSS

    Opinions on holley HP

    Just a thought, Never see much of them in the import world. My brother has a Holley HP setup on a Stealth ram 383 with procharger in a camaro and loves it. Says the self learning the majority of the map is the nice part and easy to tune. Would have to swap over to GM sensors and figure out...
  9. GreenChevelleSS

    Can I Tee together the IAC and PCV hoses?

    Just curious what everyones thought on this was? Im still running AFM at the moment so ive got to run both hoses to the coupler in front of the turbo. Can I Tee them together and just run one hose to my intake tube? I know that It might get oil in the IAC and it might pull more vacuum at idle on...
  10. GreenChevelleSS

    Driftmotion Manifold turbo Oil drain

    Hey guys looking for ideas on how to do the turbo oil drain with the driftmotion manifold. It doesnt look like the turbo sets high enough to run it into the stock drain location. I have the -10an flange for the stock location. Pictures would help to. Ive been searching for 2 days now and cant...
  11. GreenChevelleSS

    GreenChevelless's Remorse: 1992 supra build

    So I decided to make a build thread for this car instead of on my old cars thread. this is my old thread http://www.supramania.com/forums/showthread.php?10662-GreenChevelleSS-s-Supra-Engine-rebuild-and-Supra-clean-up! My new car 1992 Turbo Targa This post was started January 29, 2013 I got my...
  12. GreenChevelleSS

    Upgrading Turbo needing help deciding on the best route

    So Ive got a 57 trim ct26 on my car currently. Its finally crapping out. Im wanting to upgrade to something with some more capability. Im thinking about getting the CAST T4 manifold. But trying to figure out what turbo to get. I found a used Precision 6266 for $700 plus shipping. Guy claims is...
  13. GreenChevelleSS

    Rear upper ball joints

    Did a search and couldnt find much of anything. But today I was changing out my rear shocks and noticed that my rear upper balljoint has up and down play in it, probably a good quarter inch of play. Is there anywhere to get new ball joints or upper control arms? Havent had any luck finding any.
  14. GreenChevelleSS

    Whats it worth? Blue Cloth seats good shape

    I have full set front and rear Blue cloth seats Im trying to figure out what they are worth. They are in pretty good shape. the drivers seat shows a little wear but no rips or tears. The passengers seat is in good shape. The rear seats are in good shape with a little bit of sun fading on the...
  15. GreenChevelleSS

    How much extra material needed for door panels?

    Im thinking about buying a set of ebay seat covers for my 92. It has blue interior and im thinking about having them making the seats black with blue sticking and replacing the door panel inserts the sides of the rear seats with black to match the rest with the blue/black combo. (I dont know how...
  16. GreenChevelleSS

    ABT brake rotors on ebay

    I need some front brake rotors for the supra and instead of ordering a cheap replacement from the auto store I was wondering if anyone has tried these slotted zinc plated rotors on ebay? http://www.ebay.com/itm/170885323886?ssPageName=STRK:MEWAX:IT&_trksid=p3984.m1423.l2649
  17. GreenChevelleSS

    what is this plug?

    can anyone tell me what this plug is? When I got the car it wasnt plugged into anything and I can't find anywhere for it to plug in. Its hanging down behind the PS pump and infront of the turbo. Coming off the engine harness.
  18. GreenChevelleSS

    typical machine shop bill for head surface and valve job?

    Just curious what everyone is paying for a valve job and head surface? The machine shop I just took mine too gave me the price and I about crapped my pants.
  19. GreenChevelleSS

    Cheaper Alternative to Engine mounts 89+

    Ok so both my engine mounts are shot, and I did engine mounts on a ford not to long ago that looked quite similar so I looked through my invoices and saw it was a bronco with 4.9L that I did them on. I ordered one from advance and wow I think it will work great. My price was $29.39 for the 1991...
  20. GreenChevelleSS

    Felpro MLS head Gasket

    So I searched and couldnt find much info on it. But I was wondering what the news was with the FELPRO Permatorque MLS head gasket was. I ran it on my 90 Turbo car and never had a problem and it was, arp studs, N/A pistons, shaved block and head, 12psi boost and increased timing. I was...