Search results

hey, so i finally got my car started today after my rebuild, i had the car running for maybe 5 minutes or so, and i then shut it off to do a few things to it. when i went to start it back up, i had no fuel- the pump was doing nothing. I jumped the Fp and B+ in the diagnostic box, and still i...

can anybody tell me how to test and adjust the TPS on a 7M-GTE? i read through a couple threads about this but this will be my first time doing it and im unfamiliar with the process.. Im getting codes 14 and 51 and i dont think 51 is refering to my a/c which is why i want to check the TPS...

i was wondering if someone could tell me what each of the sensors are on the thermostat housing, and what colour the wiring is that goes to them.. i had to fix a hacked harness and i think i may have screwed up.. its a 1990 GTE harness, thanks a lot

hey everyone, i tried to start the car up today for the first time after my swap, and nothing will happen whatsoever, it does not even attempt to turn over, all i hear is the starter relay on the passenger side going off.. its a brand new battery, and im getting power to everything.. i...

hey guys, i just went to start up my car today for the first time after the rebuild, and as soon as i connect the battery, there is a buzzing/hissing coming from the kick panel where the fuses are.. i can feel which one is buzzing, but i cant seem to find a diagram or picture that tells me...

i been searching the forum and cant quite get the exact answer i need.. im wiring up a boost gauge that has 3 wires in it.. yellow: switched red: constant black: ground my question is.. can i hook ALL 3 of these wires up to wires found on the cigarette lighter? if so, which 3 wires...

hey everyone, just had a quick question.. i replaced some parts in my bottom end over the winter- main bearings and rod bearings, installed ARP connecting rod bolts, front and rear main seals, and added a new oil pump.. and i was wondering.. i did not do such things as cylinder honing...

im taping up a harness that i picked up, and i had to wire in new knock sensor connectors.. is it possible to mix up the order of them? or does it matter which connector goes on which knock sensor? kirk

hey guys, im trying to finish up gettin my motor in, and im having a little truoble with the wiring harness for my motor matching up with the harness for the body.. my motor is an 87-88 harness, and my body is a 90, i heard there are some wiring differences and i notice them now, and im not...

hey guys, ive been trying to find the souce of an oil leak, and i havent had any luck.. its leaking around the back of the block area, the tranny is where it ends up dripping from- near where it meets the block and also down a bit more towards the back, the underbody is pretty wet too around...

whats up guys, over the winter i plan on doing a bunch of mods.. its an 89T... i'll be dropping in a new fuel pump and FPR, but i'm still deciding on a couple of other things and i thought maybe someone might be able to help me out.. one the one hand (originally) i was going to just...

wats up guys, i drive an 89T, and i recently picked up my new suspension, i went with H&R springs with tokico HP's... im going to need an alignment once its all finished and i was just wondering if someone could tell me wat alignment specs are correct for the lowered vehicle (camber, toe...

my car has been getting worse and worse over the last little while, and i cant figure out the reason for it.. the car has a lot of trouble starting when the engine is cold and been sitting for a bit, anything over 4 hours or so... i crank it and crank it and EVENTUALLY it will turn over, but...

i need some help with something that im not too sure of... something wierd happened yestrday and i dont know wat to do.. i disconnected my amp do replace it with a better one last nite, and everything went good.. but then today i went to turn off my car, and the clock and my deck wouldnt turn...