Search results

symptoms: Fuel Relay buzzes constantly and the car is always on. I have to pull the negative cable of the battery. and when I try to start it all it does is crank over. it has all new ground straps, plugs and wires, cap, rotor, starter, and everything is in time. I also have this plug...

I got it all figure out!! Thanks for the help guys :D

Engine is fully assembled on the lower end. I was told it was shaved down before i bought the car and it came with no cylinder head. I just aquired a rebuilt head and i want to get the correct HG. Thanks guys!! i have called every source i can and no one even knew a stock height. THANKS A TON!!!

I tried searching with no luck. I have an 87 7MGE and i got it with no head on it. I was told it was shaved and I have no record or document to prove so. I have aquired a rebuilt N/A cylinder head and I would like to know how to find the deck height so I can get the correct HG for it...

Here are some pics I just took.. Im bout to strip it back down and prep everything for primer and sealer, then off to paint. Gotta have it ready for my road trip to Boise/Nampa, ID in March :D :icon_bigg

Well I got some huge news (to me anyways) I picked up the fenders, header panel and headlight assemblies I got 2 87 Canadian Market Burghandy Fenders, Canadian Market Burghandy Header Panel (for you keen eyes, only CAN markets had the headlight squirters) & Both 87 White Headlight...

Well I am not understanding why I am getting no replies on here, i was recommended to come here to a great forum, and i am not getting the help i am looking for. Come on guys, I don't bite!!! On a side note, I need the following parts Driver Side Headlight Cover Driver Side...

I should be able to. I am looking at around $800 for an Imported 7MGE with all the accessories and whatnot with around 40k miles. Then i gotta pull the head, replace the head gasket, install ARP studs and torque down to 74ft-lbs i think it is. I will give it a tune up and what not. I...

it would cost more to rebuild the bottom end, buy a 7mge head and try and replace the top end stuff i dont have... then to buy a new one/imported one.

Not a problem Caleb. and i am just trying to get the engine, front axle and transmission from my 4Runner sold. I need money for a new 7MGE

Welcome to the supra scene buddy!!! also ill be pulling those axle shafts for you soon. it's gonna be snowing soon.

I am interesting in the following wheels: ADR Type 79 Battle Axe 17x7s/18x8.5s Enkei LS5 18x8s Stern ST1 18x8s TSW Volcano 17x7s TSW Track Star 17x8s/18x8s Motegi Trak Lite 17x8s Raceline Type 126 17x7.5s Feedback? I like all of these.

Alright got the 7MGE pulled out tonight. I am going to pull all the crap out of the engine bay I can.... steam clean it, sand it down.... primer it and get some good coats of gloss black paint on it. anything i took out, will be cleaned and painted. I thought about painting the Valve Covers...

i could use both the nose panel and bumper piece too. is the bumper straight? it's hard to tell from the pics you have posted.

Well I sold the 3.0 3VZ V6 out of my 90 4Runner im parting out and I am pulling it this week for the guy i sold it to to help fund the Supra... While i have the cherry picker over I am going to pull the 7MGE Block from the Supra as well. I have never pulled one, so I have no idea what all...

I voted Whaletail, as its super sleek and low profile. Its the look im goin for

I'll watch, That's a nice supra. gets lots of pics of your swap.

Driftmotion sells those, I was on there site early this morning. any info on some 2JZGE's would be awesome. i'd swap mine to that if I could find one and have the swap stay right about $800, as I was planning on dropping the money tax time on a 47k miles JDM JMGE imported from Japan from a place...

Thanks buddy. Lots of little stuff that I need. and for around 800 bucks?