Search results

We are getting close to the annual Tampa meet. Is there anything in the works for November?

How do I connect the vacuum lines etc from the maft pro boost solenoid to a HKS wastegate? The HKS gate has 1 nipple on the side and 1 on top. I do not want to tap a vac source in the new turbo compressor housing.

Any dates?

I am beyond the point of composure right now. I have an upgraded 60 trim CT that has been sent back for repairs 3 times and now needs to go back again. The last 2 times I only had the turbo on the car for 3-4 days.. I have done fresh oil and filter changes, Prime the turbo properly, use...

I have finally built the 7m and used a 2mm Titan MS HG.. The question I have is now that I am using the MHG do you still have to put silicone on the 2 places (front) between the head and block or was this just an issue with using a stock gasket? Thanks, Matt

I found a few post on replacing the crank pulley but need a little more info. My engine is being built and I was wondering if the lightweight Crank pulley would be ok to use? I know the stock one has the damper in it. If my engine is being balanced with a lightweight pulley what would it hurt?

I am in the middle of my build up and I am replacing the clutch. Should I use a 6 puck rigid or sprung disk. My build when finished will be .20 JE's, Eagle Rods, ARP hardware, MHG, RS-RGT2 exhaust, Spearco replica,60-1 CT @ 18psi and the rest in my sig. I am already running a ACT HD PP...

Just a FYI.. I am finally working on the 7m build and I am getting my pistons coated. Just wanted to share this info for those who don't know! Piston Crown http://www.swaintech.com/store.asp?pid=10963 Piston Skirt http://www.swaintech.com/store.asp?pid=10964 I am getting the...

Does anyone know of a shop that builds 7m's? I would hope that the shop uses a 7m torque plate. I cannot find a shop here in Jacksonville that has a 7m torque plate. I am looking to do a performance build. (pistons, rods..etc) I did read the shops in your area post. Alabama might be a...

I notice when I start my car (or turn the ignition on).. The maft pro is reading the setup page.. I used to have it on the sensor monitor page and it always stayed there.. Is there a battery on the board that would retain this setting?? The wires are connected with the taps (Bad I Know)...

Me and Black87Turbo are ready to send the blocks to the shop. Both of us have been doing a lot of research thanks to the posts in the engine buildup area. We have just read too many opinions and are not real sure what to use. Would like a response from guys that have done builds and are...

Let me just start by saying I know!!! Search!! I have read alot about what sizes people have just haven't seen anything like these.. I should just keep the sawblades but.. These are ok.. Here it is.. Racing Hart Rear- 19x10 offset 43 w/Michelin Pilot 275/30/19 Front-19x8.5 off 39...

I know there is a parts review section but I thought this may be useful.. Here is a question answered by Powerslot Tech.. Question: I just purchased a set of PS Rotors for my 89 Supra turbo. I have been doing some reading and your install sheet suggests Hawk pads. I am having a hard time...

My antilock light is on and my power steering is out.. Plenty of fluid and no codes.. Any ideas??

Notice I am the only MKIII at the boat ramp... My MKIII brotha's left me.. Dang!!!

http://videos.streetfire.net/search/grand+national/0/0fba4999-0f15-478b-9693-164e9c14ff1c.htm

Tuning the MaftPro and this is my latest at Idle. Can one of you maft pro wizards tell me if everything looks cool..

I notice driving home the other day I pushed in my clutch and felt the pedal give a little.. Hmmm maybe air in the lines??? So I call a fellow Supra owner and volunteers to come by after work and help me bleed the clutch.. Well the pedal felt like it was scraping something when I pushed it...

My car idles around 650rpm and when I turn my AC on it drops to 500 or just below. Almost shuts off. When I have to stop as soon as I push in the clutch the car will idle to loww and shut off. What would cause the car not to Idle up when the AC is turned on?

Well I am up and running and man it feels GREAT!!! Has been down a couple of months and now I am on the road again.. I LOVE THIS CAR!!! I do have a quick ?? on the tune.. My idle AFR is right at 14.7 :icon_bigg when i rev it my AFR's go to 10 or so and blows the black cloud.. How...