Recent content by Overboostin007

  1. O

    Tech Info Needed On 7mgte

    Or you can do what i did. I ran a ford eb i think it was 3 inch throttle body which is a 3 wire TPS as it has earth, signal and power. Much easier to work with then the toyota TPS. Not sure how you go adapting that to the inlet manifold though as mine was custom
  2. O

    What Tha???

    Well i haven't added any new wiring. I've used the same abs sensor and wiring, and the speedo isn't hooked up. And the shifting locater from the auto is sitting aside in Park position (thats what lets the fuel pump engage).
  3. O

    What Tha???

    Ok just got my new engine in after many probs along the way with the manual conversion. Got everything hooked up and the manual gear all in place. Put the finishing touches on her and hook the battery up and the fuel pump relay near the drivers side tems unit start buzzing and the dash all...
  4. O

    7mgte Tps Voltage Output Needed

    Hey guys i am after the voltage output on the throttle positioning sensor on the 7mgte. I have worked out both wires on the tps harness side and my larger ford 3 inch throttle body that has three wires. But however the voltage outputs are somewhat of a difference some i need to put some...
  5. O

    Fuel cut >_<

    what a joke. I ran 19psi on my old engine with a mines fuel hacker and blitz turbo which adjusted fuel ratio. But my point is i had 440 injectors and they didn't max out till 20psi.
  6. O

    Tech Info Needed On 7mgte

    I have a ford v8 throttle body on a custom plenum. The tps on the ford tb is a 3 wire. And my plug a four. I was wondering if i could do away with one wire. but being that they are not a kick down wire i can't just cut one. Just have to work out now how to convert to a 3 wire
  7. O

    Tech Info Needed On 7mgte

    I am after the order from left to right of the coilpack in which the leads go on as my coil pack isn't number. Also i have changed my throttle body to a lager one and the new tps has 3 wires whereas the old 7mgte one has 4. One of those four is for the kick down switch for the auto to know when...
  8. O

    MKIII 7MGE and 7MGTE SPECS

    Hey mate i got if of the www.supraforums.com.au which i am also a member of. Just thought it would be handy
  9. O

    MKIII 7MGE and 7MGTE SPECS

    SPECIFICATIONS ENGINE Valve Clearance (engine cold), mm (in.): Intake 0.15 - 0.25 (0.006 - 0.010) Exhaust 0.20 - 0.30 (0.008 - 0.012) Spark Plug Type: 7M-GE NIPPONDENSO PQ16R NGK BCPR5EP11 7M-GTE NIPPONDENSO PQ20R-P8 NGK BCPR6EP-N8 Spark Plug Gap, mm (in.)...
  10. O

    7MGTE torque specs?

    will do. I have a car show on the first of may. And there's a burnout comp. Might put her in and she what clouds i can create
  11. O

    7MGTE torque specs?

    hey guys thanks for the settings. I will have my engine back together next week and after making 469rwhp on the last engine i'm hoping for a bit better number this time. Although i have to get a new ecu as the last aftermarket on is stuffed. Will keep you updated cheers
  12. O

    7MGTE torque specs?

    hey mate so the main caps are 75ft pound. Do you know what the arp rod bolts tension are?
  13. O

    7MGTE torque specs?

    yeah they are standard main cap bolts. I bought the engine with arp rod bolts. And i have the arp moly based lube that i got with my head studs.
  14. O

    Old members roll call.

    ok i'm here too
  15. O

    7MGTE torque specs?

    I am after the torque settings for standard main bolts and settings for arp rod bolts. if any one knows could you let me know thanks
See more
Top Bottom