Powered by Team Mondor
Results 1 to 4 of 4

Thread: Questions about switching over to Sequential injection - AEM V1, ID1000's

  1. #1
    Lurker
    wisetechscottt's Avatar
    Join Date
    Sep 2015
    Location
    Detroit
    Posts
    12

    Default Questions about switching over to Sequential injection - AEM V1, ID1000's

    Hey guys, I picked up an 87 turbo about 6 months ago as a new project. I’m getting ready to pull the engine and strip the car down to get it into the body show and get it painted. I have some issues that I want to take care of before I tear it all down so that I know the car runs good as a benchmark when I go to put it all back together.

    So here is my question, I have been gathering info from all over the place on swapping the car over to sequential injection and I just want to run this by someone to make sure that my understanding is where it needs to be.

    I heard there was a guide somewhere , but for the life of me I can’t find it. SO if this was coved in depth somewhere else, sorry for the duplication.
    The car is currently managed by an AEM EMS V1 ( 31-1110 ), with ID1000’s

    Wiring:
    Injectors 4, 5, 6 - the ground trigger is wired to the to each of extra pins as indicated in the AEM diagram ( 2-10, 2-11, 2-12 for the 31-1110).
    As the car is currently using the ID1000’s there is no resistor box and will have no need to use one in sequential either as the ID1000’s are high impedance. The power source remains unchanged.

    AEM Settings:
    Injector Setup:
    Injectors ( 1,2,3,7,8,9,10) – set to active, 02 feedback 1 & Primary
    Injectors ( 4,5,6) – nothing selected

    Change Injector Phasing to the following:
    Injector Phase = 0
    Inject Tooth #01 = 19.00
    Inject Tooth #02 = 11.00
    Inject Tooth #03 = 3.00
    Inject Tooth #04 = 0
    Inject Tooth #05 = 0
    Inject Tooth #06 = 0
    Inject Tooth #07 = 15.00
    Inject Tooth #08 = 23.00
    Inject Tooth #09 = 7.00
    Inject Tooth #10 = 0

    Change Fuel teeth from 12 to 24
    100% increase of entire fuel map
    I believe that this should be all that I need to do to flip the car from batch injection to sequential while running into the least amount of issues…lol.

    Is there anything that I’m missing or have stated wrong?

    Thanks for any help!

  2. #2
    Lurker
    wisetechscottt's Avatar
    Join Date
    Sep 2015
    Location
    Detroit
    Posts
    12

    Default Re: Questions about switching over to Sequential injection - AEM V1, ID1000's

    Come on guys....There has to still be some V1 gurus out there...lol

  3. #3
    Grease Monkey

    Join Date
    Jul 2009
    Location
    Calgary
    Posts
    161

    Default Re: Questions about switching over to Sequential injection - AEM V1, ID1000's

    Looks correct, I might go with slightly different phasing.

    The info you are looking for is here:
    http://www.supramania.com/forums/sho...than-200/page4

    Starts around page 4, but it is all good reading.
    Torrid red '84 P-type, Black and Grey leather, Fully Restored

    Built 7MGTE, AEM V1 EMS, R154, BOSS 60mm GT turbo, 2 1/2" IC and 3" exhaust, the works

    ROH wheels, Coilovers, BBK, Konis, Addco bars etc. etc.

    450 RWHP at 12psi, on 650CC injectors.

  4. #4
    Lurker
    wisetechscottt's Avatar
    Join Date
    Sep 2015
    Location
    Detroit
    Posts
    12

    Default Re: Questions about switching over to Sequential injection - AEM V1, ID1000's

    i'll take a look .. thanks for the insight cheeze

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •