PDA

View Full Version : Oil in Distributor Cap



landtoy80
07-23-2007, 10:18 PM
I have a oil leak in under the dist cap.
Did a search and found its what I thought it was, the seal.
I keep seeing "CPS", what is or does CPS stand for?
Is there a page with all the acronyms for this site?

I was going to install new cap and rotor, should I wait on the cap and rotor until I replace the seal?

SupaMan
07-23-2007, 10:24 PM
I have a oil leak in under the dist cap.
Did a search and found its what I thought it was, the seal.
I keep seeing "CPS", what is or does CPS stand for?
Is there a page with all the acronyms for this site?
cps is cam position sensor on turbos its in the same place as our distruber would be.


hopefully i got that right because im tired and cant think

IJ.
07-23-2007, 10:25 PM
Crank Position Sensor or Cam Position Sensor sort of interchangeable for our car as the Distributor/CPS has sensors for both in one unit.

There's a sealed bearing under the reluctor star wheel that in your case sounds like it's leaking.

No use installing the new parts until you correct this.

suprageezer
07-23-2007, 10:28 PM
Inside the distributor theres a small hole, is that where the oil is coming from? if it is thats the seals in the sealed bearings of the dist shaft bearings. Mine was leaking I thought it was the oring but NOOOO it was those seals, the oil caused the underside of the electronics to crak then it started shorting out. I ended getting lucky and buying a rebuit beck arnley dist off ebay for 39.00.

SupaMan
07-23-2007, 10:31 PM
Crank Position Sensor or Cam Position Sensor sort of interchangeable for our car as the Distributor/CPS has sensors for both in one unit.

There's a sealed bearing under the reluctor star wheel that in your case sounds like it's leaking.

No use installing the new parts until you correct this.
sweet thanks for clearin that up.

landtoy80
07-23-2007, 11:10 PM
Can't really tell if the oil is from the hole or is flowing there.
There is only a small drop of oil from the hole.
If the replaceable o-ring rubber seal is leaking, where in the dist would the oil be leaking?

I can see sings of oil leak where the dist mounts to the motor.

There is part of a thin (about the thickness of a paper clip) seal sitting lose under the cap.
Is that the o-ring seal or the non replaceable seal?

CRE
07-23-2007, 11:40 PM
The hole, IIRC, is just a weep to direct any leaks away from the electronics. There is a seal on the outside of the shaft housing and then inside there's a bearing with a built in seal between the shaft and the housing. If the outer seal leaks you get oil running down the side of the engine from the base of the dist. If you've got oil inside the distributor the bearing's seal has most likely failed.

People have found a replacement sealed bearing for the CPS, but I don't know if the same one will work in the dist.

landtoy80
07-27-2007, 10:37 PM
Before I go and order a OEM new/rebuilt dist, is there a nonUSA version dist like the Land Cruisers have or is there a better after market dist?

landtoy80
07-27-2007, 10:46 PM
Is this what I need, will it work in the dist?
http://www.twosrus.com/catalog/product_info.php?cPath=41&products_id=66&osCsid=6bec8e0ccd13a73f4366341e6e149624
http://www.twosrus.com/catalog/images/DSCF0017.JPG

IJ.
07-27-2007, 11:13 PM
NA Distributor and GTE CPS use different size shafts so the bearings are different.

landtoy80
07-30-2007, 10:52 AM
I found a rebuilt dist at http://ww1.autopartauctions.com/a.asp?A=546804&ap=5830&C=13&G=
Anyone know about Autopartauctions.com? Are the parts they sell used or new/rebuilt and unused?

Anyone have luck with a used dist?

landtoy80
08-02-2007, 11:07 PM
I found a rebuilt dist at http://ww1.autopartauctions.com/a.asp?A=546804&ap=5830&C=13&G=
Anyone know about Autopartauctions.com? Are the parts they sell used or new/rebuilt and unused?

Anyone have luck with a used dist?

I won the auction, will see is it works when it gets here.

suprageezer
08-04-2007, 07:12 PM
Thats what I bought in ebay, mine works great. Good Luck

landtoy80
08-12-2007, 11:56 PM
Got the dist and it looks fine.
At local repair shop that sells Beck Arnley parts, the part listed at $400.
I seen it online for around $200.
How is it that it can be sold for $55?

suprageezer
08-13-2007, 04:10 PM
I just figured some shop owner must have had it sitting on their shelves for eons and decided to get it off the books by throwing it on ebay, that's my guess.